ADP1828LC-EVALZ Analog Devices Inc, ADP1828LC-EVALZ Datasheet

no-image

ADP1828LC-EVALZ

Manufacturer Part Number
ADP1828LC-EVALZ
Description
BOARD EVALUATION ADP1828LC
Manufacturer
Analog Devices Inc
Datasheets

Specifications of ADP1828LC-EVALZ

Main Purpose
DC/DC, Step Down
Outputs And Type
1, Non-Isolated
Voltage - Output
1.8V
Current - Output
5A
Voltage - Input
5.5 ~ 13.2V
Regulator Topology
Buck
Frequency - Switching
600kHz
Board Type
Fully Populated
Utilized Ic / Part
ADP1828
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
EVALUATION BOARD DESCRIPTION
This data sheet describes the design, operation, and test results
of the ADP1828 5 A evaluation board. The input range for this
evaluation board is 5.5 V to 13.2 V, and the output voltage is 1.8 V
with a maximum load current of 5 A. For this design, a switching
frequency (f
between efficiency and the sizes of the power components.
ADP1828 DEVICE DESCRIPTION
The ADP1828 is a synchronous PWM voltage mode buck
controller. It drives an all N-channel power stage to regulate an
output voltage as low as 0.6 V to 85% of the input voltage and is
sized to handle large MOSFETs for point-of-load regulators. The
ADP1828 is ideal for a wide range of high power applications,
such as DSP and processor core I/O power, as well as general-
purpose power in telecommunications, medical imaging, PC,
Rev. 0
Evaluation boards are only intended for device evaluation and not for production purposes.
Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or
statutory including, but not limited to, any implied warranty of merchantability or fitness for a
particular purpose. No license is granted by implication or otherwise under any patents or other
intellectual property by application or use of evaluation boards. Information furnished by Analog
Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result
from its use. Analog Devices reserves the right to change devices or specifications at any time
without notice. Trademarks and registered trademarks are the property of their respective owners.
Evaluation boards are not authorized to be used in life support devices or systems.
ADP1828
SW
) of 600 kHz is chosen to achieve a good balance
DIGITAL PICTURE OF THE BOARD
Figure 1. ADP1828 5 A Evaluation Board
DISK DRIVE POWER CONNECTOR
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
gaming, and industrial applications. It operates from an input
voltage of 3 V to 18 V with an internal LDO that generates a 5 V
output for a V
The ADP1828 operates at a pin-selectable, fixed switching
frequency of either 300 kHz or 600 kHz, or at any frequency
between 300 kHz and 600 kHz if a resistor is used. The
frequency can also be synchronized to an external clock up to
2× the switching frequency. The clock output can be used for
synchronizing the ADP1828 or another part, such as the
ADP1829, thus eliminating the need for an external clock
source. The ADP1828 includes soft start protection (to limit
inrush current from the input supply during startup), reverse
current protection during soft start for a precharged output,
voltage tracking, power good, as well as an adjustable lossless
current-limit scheme utilizing external MOSFET sensing. The
ADP1828 is offered in a 20-lead QSOP package.
Step-Down DC-to-DC Controller
IN
of 5.5 V to 18 V.
5 A Evaluation Board for
©2007 Analog Devices, Inc. All rights reserved.
EVAL-ADP1828LC
VIN TERMINAL
GND TERMINAL
ACTIVE AREA
GND TERMINAL
DUAL FET Si7958DP
VOUT TERMIINAL
www.analog.com

Related parts for ADP1828LC-EVALZ

ADP1828LC-EVALZ Summary of contents

Page 1

... DIGITAL PICTURE OF THE BOARD DISK DRIVE POWER CONNECTOR Figure 1. ADP1828 5 A Evaluation Board One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 5 A Evaluation Board for EVAL-ADP1828LC of 5 VIN TERMINAL GND TERMINAL ACTIVE AREA GND TERMINAL DUAL FET Si7958DP VOUT TERMIINAL www ...

Page 2

... EVAL-ADP1828LC TABLE OF CONTENTS Evaluation Board Description......................................................... 1 ADP1828 Device Description......................................................... 1 Digital Picture of the Board ............................................................ 1 Revision History ............................................................................... 2 Component Design .......................................................................... 3 Input Capacitor............................................................................. 3 Inductor Selection ........................................................................ 3 Output Capacitor Selection......................................................... 3 MOSFET Selection....................................................................... 3 Soft Start ........................................................................................ 3 Current Limit ................................................................................ 3 REVISION HISTORY 8/07—Revision 0: Initial Version Switching Noise and Overshoot Reduction...............................4 Compensation Design ...

Page 3

... D is the duty cycle the inductance of the inductor. In this design, R VGS of 4.5 V. Because L is chosen to be 1.8 μH, Δ 1 standard value of 2.87 kΩ is chosen. Keep in mind that R Rev Page EVAL-ADP1828LC . Switching speed is not critical because DSON , and is adequate for handling JA = 015 × ...

Page 4

... EVAL-ADP1828LC of the MOSFET can vary by more than 25% from part to part, and by more than 50% over the temperature range; therefore, the actual current limit can vary by more than 50% from part to part over the temperature range. For more information on this topic, see the ADP1828 data sheet. ...

Page 5

... CH3 1.00V Figure 5. Soft Start INPUT RIPPLES A CH1 3.60V f = 600 kHz 1.8V OUT T = 25° CH1 3.000V Rev Page EVAL-ADP1828LC T V (AC-COUPLED) OUT STEP LOAD 4 CH1 100mV M 200µs A CH4 B W CH4 2.00A Ω Figure 6. Load Transient Load = ( (AC-COUPLED) OUT ...

Page 6

... EVAL-ADP1828LC 1.806 1.804 1.802 1.800 1.798 1.796 1.794 1.792 1.790 1.788 LOAD (A) Figure 9. Load Regulation Rev Page 1.797 1.796 2A LOAD 1.795 1.794 1.793 1.792 1.791 1.790 5A LOAD 1.789 1.788 1.787 (V) IN Figure 10. Line Regulation 11 13 ...

Page 7

... out of phase. = 600 kHz greater than 5 MOSFETs (Vishay Si7958DP Rev Page EVAL-ADP1828LC Function CLKSET = high sets CLKOUT to 2 × f OSC CLKSET = low sets CLKOUT to 1 × f OSC VREG 600 kHz SW GND 300 kHz enables ADP1828 EN = off disables ADP1828 Short VREG to V when V ...

Page 8

... EVAL-ADP1828LC Table 4. Miscellaneous Information Parameter Switching Frequency Dual Power MOSFETs: Q1A and Q1B Inductor VREG and V IN Snubber Circuit Gate Resistors Capacitor C17 Voltage Divider Comment The switching frequency set to 600 kHz (Jumper JP2) on the evaluation board different needed, the compensation and the power components need to be recalculated ...

Page 9

... EVALUATION BOARD SCHEMATIC /16V/X5R/1210 22uF /6.3V/X5R/1206 6V/X5R/1210 22uF/1 /6.3V/X5R/1210 /16V/X5R/1210 22uF fitted 7 OPEN Figure 11. ADP1828 5 A Evaluation Board Schematic Rev Page EVAL-ADP1828LC 06906-011 47uf 100uF not ...

Page 10

... EVAL-ADP1828LC EVALUATION BOARD LAYOUT Figure 12. Silkscreen Layer Figure 13. Top Layer Figure 14. Second Layer Figure 15. Third Layer (GND Layer) Figure 16. Bottom Layer Rev Page ...

Page 11

... Vishay Vishay Vishay Taiyo Yuden Murata Toko (Würth Elektronik mA, SOD-323 Vishay F Vishay Molex Inc. Any Any Any Analog Devices Rev Page EVAL-ADP1828LC Part No. GRM32ER61C226KE20 GRM32ER60J107ME20 GRM31CR60J476ME20 VJ0603Y154KXJA VJ0603Y104MXQ TMK107BJ224MA-T GRM188R61A224KA61 CRCW06030R00F CRCW06032002F CRCW06031002F CRCW06034220F CRCW06037501F CRCW06031003F CRCW06032801F CRCW08053R01F VJ0603Y122KXXA VJ0603Y102KXXA ...

Page 12

... EVAL-ADP1828LC ORDERING GUIDE Model Description 1 ADP1828LC-EVALZ Evaluation Board RoHS Compliant Part. ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. ESD CAUTION EB06906-0-8/07(0) Rev Page ...

Related keywords