EDK2329 Renesas Electronics America, EDK2329 Datasheet
EDK2329
Specifications of EDK2329
Related parts for EDK2329
EDK2329 Summary of contents
Page 1
... EDK2329 U M SER ANUAL F H8S/2329 FLASH M N CHIP ICROCONTROLLER ...
Page 2
Preface Cautions 1. This document may be, wholly or partially, subject to change without notice. 2. All rights reserved. No one is permitted to reproduce or duplicate, in any form, a part or this entire document without Hitachi Micro Systems ...
Page 3
T C ABLE OF ONTENTS ............................................................................................................................................. 3 ABLE OF ONTENTS ....................................................................................................................................... 4 TART UP NSTRUCTIONS 2.1. INSTALLING THE EVALUATION DEVELOPMENT KIT (EDK)........................................................................... 4 2.2. SERIAL CONNECTION ....................................................................................................................................... 4 2.3. POWER SUPPLY ................................................................................................................................................ ...
Page 4
TART UP NSTRUCTIONS 2. NSTALLING THE VALUATION Please refer to the quick start guide provided for initial installation of the EDK. A copy of the quick start guide and other information relating to this ...
Page 5
EDK B L OARD AYOUT The diagram shows a general layout of the EDK board. FLASH Programming Power NMI Switch BOOT LED Power LED User1 LED User2 LED RESET BOOT Switch Switch CJ5 9-Way D-Type CJ4 3.1. EDK B ...
Page 6
EDK O PERATION 4.1. USER INTERFACE The EDK provides three buttons for influencing the operation of the board. The purpose of each button is clearly marked next to it. Refer to the board layout for positions (Figure 3.1) 1. ...
Page 7
C C RYSTAL HOICE The operating crystal frequency has been chosen to support the fastest operation with the fastest serial operating speeds. The value of the crystal is 22.1184MHz. The following table shows the baud rates and Baud Rate ...
Page 8
M M EMORY AP Table 4-4 illustrates the EDK memory map for mode 6. Section End Section Start H’00000000 H’0000FFFF H’00010000 H’0005FFFF H’00060000 H’0007FFFF H’00080000 H’00FF73FF H’00FF7400 H’00FF7BFF H’00FF7C00 H’00FFFBFF H’00FFFC00 H’00FFFE4F H’00FFFE50 H’00FFFF07 H’00FFFF08 H’00FFFF27 H’00FFFF28 H’00FFFFFF 4.5. ...
Page 9
B O OARD PTIONS The EDK has a number of configuration settings set by jumpers CJ4 ( D), CJ5 ( and zero-ohm links. Common EDK functions can be set using the jumpers as described ...
Page 10
– CJ5 SER ODE ETTINGS CJ5 is used to set the operating mode of the microcontroller. These jumpers must be fitted at all times to ensure correct operation of the EDK. Jumper CJ 5-A User Mode ...
Page 11
ERIAL ORT ELECTION The programming serial port is connected to the RS232 connector by default. This allows direct programming of the EDK using the supplied software tools. A secondary serial port is available on the microcontroller ...
Page 12
XTERNAL EBUG EADER The External debug header may be used with the Hitachi E10A Debugger or a third party debugger. The E10A is an on-chip debug emulator available separately from Hitachi. This header provides direct access ...
Page 13
S D TATE IAGRAM Async Boot Mode Controller : Positive Logic (CTS+BootSw) . /Res Waiting Reset Timer /Res ResSw . /Res Res /Res . Reset Reset (BootSW + ResSw + CTS) . /Res F 5-2: CPLD S D IGURE ...
Page 14
C D ODE EVELOPMENT 6.1. HMON 6.1. ODE UPPORT The HMON library is built to support modes and 7. 6.1. REAKPOINT UPPORT H8S/2329 has no break controller, therefore there no breakpoints can ...
Page 15
M M EMORY AP H'00000000 Vectors H'00001000 FDTInit H'00001119 H'00002000 CUser_Vectors H'00002003 H'00005000 PHMON CHMON H'00007421 On-Chip FLASH ROM H'0000F600 FDTUserMode MicroKernel H'0000FE46 H'00080000 EXTERNAL RAM H'000BFFFF H'00FF7C00 On-Chip RAM H'00FFF700 BHMON H'00FFF90F H'00FFFA00 Stack H'00FFFBFF H'00FFEFBF H'00FFFE50 Internal ...
Page 16
AUD ATE ETTING HMON has initially set to connect at 115200Baud. Should the user wish to change this, the value for the BRR in HMONserialconfiguser.c will need to be changed and the project re-built. Please refer ...