EDK3687 Renesas Electronics America, EDK3687 Datasheet
EDK3687
Specifications of EDK3687
Related parts for EDK3687
EDK3687 Summary of contents
Page 1
... EDK3687 U M SER ANUAL F H8/3687 FLASH M N CHIP ICROCONTROLLER ...
Page 2
Preface Cautions 1. This document may be, wholly or partially, subject to change without notice. 2. All rights reserved. No one is permitted to reproduce or duplicate, in any form, a part or this entire document without Renesas Technology Europe ...
Page 3
T C ABLE OF ONTENTS ............................................................................................................................................. 3 ABLE OF ONTENTS ....................................................................................................................................... 4 TART UP NSTRUCTIONS 2.1. INSTALLING THE EVALUATION DEVELOPMENT KIT (EDK)........................................................................... 4 2.2. SERIAL CONNECTION ....................................................................................................................................... 4 2.3. POWER SUPPLY ................................................................................................................................................ ...
Page 4
TART UP NSTRUCTIONS 2. NSTALLING THE VALUATION Please refer to the quick start guide provided for initial installation of the EDK. A copy of the quick start guide and other information relating to this ...
Page 5
EDK B L OARD AYOUT The diagram shows a general layout of the EDK board. FLASH Programming Power NMI Switch Power LED User1 LED User2 LED RESET Switch 9-Way D-Type CJ4 3.1. EDK B D LOCK IAGRAM The diagram ...
Page 6
EDK O PERATION 4.1. USER INTERFACE The EDK provides two buttons for influencing the operation of the board. The purpose of each button is clearly marked next to it. Refer to the board layout for positions (Section 3) 1. ...
Page 7
C C RYSTAL HOICE The operating crystal frequency has been chosen to support the fastest operation with the fastest serial operating speeds. The value of the crystal is 18.432MHz. The following table shows the baud rates and Baud Rate ...
Page 8
I2C EEPROM The board has been tested with an Atmel AT24C04AN-10SI-2.7 I2C EEPROM device (Not supplied). The device is configured to connect to dedicated I2C pins on Ports P56 and P57. 4.5. LIN I NTERFACE The board has been ...
Page 9
B O OARD PTIONS The EDK has a number of configuration settings set by four jumpers CJ4 ( and zero-ohm links. Common EDK functions can be set using the jumpers as described in sections 5.2. The ...
Page 10
EDK O – CJ4 PTIONS The EDK options provide access to commonly used features of the EDK range. These jumpers must be fitted at all times to ensure correct operation of the EDK. Jumper Function CJ 4-A Serial Receive ...
Page 11
PTION INK ELECTION The following sections show the option links that apply to each peripheral device. The tables all use the same key of symbols which is given below: X – Groups of options one set ...
Page 12
SPI – ERIAL ERIPHERAL The SPI interface is not directly compatible with the SCI interface on the device. Selection of the connections to the SPI interface should therefore be chosen to allow the operation of other peripherals ...
Page 13
M H ICROCONTROLLER EADER The following table lists the connections to each or the headers on the board. 6. EADER Pin Function EDK Symbol No 1 TEST GND 3 VCL NC3 (No Connection CON_X2 7 ...
Page 14
C D ODE EVELOPMENT 7.1. HMON 7.1. ODE UPPORT The HMON library is built to support Normal Mode only. 7.1. REAKPOINT UPPORT The monitor utilises the Address Break Controller for code located in ROM, allowing ...
Page 15
M M EMORY AP H'0000 Vectors H'0400 FDTInit H'04F7 H'0500 FDTUserModeMicr oKernel H'0BC1 H'0C00 CUser_Vectors H'0C03 H'1000 PHMON CHMON H'2D10 On-Chip FLASH ROM H'DFFF H'E800 On-Chip RAM H'EFFF H'F700 Internal I/O REGISTERS H'F77F H'F780 On-Chip RAM H'FC7F H'FC80 BHMON ...
Page 16
... I NTERRUPT MASK SECTIONS The EDK3687 has fixed interrupt priorities. The serial (SCI3 )port interrupt is used by HMON. The Real Time clock, external interrupt and Timer V interrupts have a higher priority than the serial port. If these interrupts are used HMON may not function correctly. ...