EDK2239 Renesas Electronics America, EDK2239 Datasheet

Page 1

... EDK2239 U M SER ANUAL F H8S/2239 FLASH M N CHIP ICROCONTROLLER ...

Page 2

Preface Cautions 1. This document may be, wholly or partially, subject to change without notice. 2. All rights reserved. No one is permitted to reproduce or duplicate, in any form, a part or this entire document without Hitachi Micro Systems ...

Page 3

T C ABLE OF ONTENTS ............................................................................................................................................. 3 ABLE OF ONTENTS ....................................................................................................................................... 4 TART UP NSTRUCTIONS 2.1. INSTALLING THE EVALUATION DEVELOPMENT KIT (EDK)........................................................................... 4 2.2. SERIAL CONNECTION ....................................................................................................................................... 4 2.3. POWER SUPPLY ................................................................................................................................................ ...

Page 4

TART UP NSTRUCTIONS 2. NSTALLING THE VALUATION Please refer to the quick start guide provided for initial installation of the EDK. A copy of the quick start guide and other information relating to this ...

Page 5

EDK B L OARD AYOUT The diagram shows a general layout of the EDK board. FLASH Programming Power NMI Switch BOOT LED Power LED User1 LED User2 LED RESET BOOT Switch Switch CJ5 9-Way D-Type CJ4 3.1. EDK B ...

Page 6

EDK O PERATION 4.1. USER INTERFACE The EDK provides three buttons for influencing the operation of the board. The purpose of each button is clearly marked next to it. Refer to the board layout for positions (Section 3) 1. ...

Page 7

C C RYSTAL HOICE The operating crystal frequency has been chosen to support the fastest operation with the fastest serial operating speeds. The value of the crystal is 14.745MHz. The following table shows the baud rates and Baud Rate ...

Page 8

Alternatively the device may be programmed using SCI2, but configured to use the debug serial port (SCI0), as detailed in section 5.4, for access to the full address range (256k x 16). The SRAM, (when fitted), is connected to Chip ...

Page 9

B O OARD PTIONS The EDK has a number of configuration settings set by jumpers CJ4 ( CJ5 ( and zero-ohm links. Common EDK functions can be set using the jumpers as described ...

Page 10

– CJ5 SER ODE ETTINGS CJ5 is used to set the operating mode of the microcontroller. These jumpers must be fitted at all times to ensure correct operation of the EDK. Jumper CJ 5-A User Mode ...

Page 11

ERIAL ORT ELECTION The programming serial port is connected to the RS232 connector by default. This allows direct programming of the EDK using the supplied software tools. A secondary serial port is available on the microcontroller ...

Page 12

B C OOT ONTROL The method for placing the microcontroller device in to Boot mode for reprogramming has been incorporated into a complex programmable logic device (CPLD). This is not necessary for most user designs but allows a measure ...

Page 13

M H ICROCONTROLLER EADER The following table lists the connections to each or the headers on the board. 6. EADER Pin Function EDK Symbol No 1 STBY STBYn 3 RES RESn 5 OSC2 CON_OSC2 7 MD0 MD0 ...

Page 14

H J2 EADER Pin Function EDK Symbol No 1 XTAL CON_XTAL 3 EXTAL CON_EXTAL 5 MD2 MD2 7 PF6/AS PF6 9 PF4/HWR PF4 11 PF2/WAIT PF2 13 PF0/BREQ/IRQ2 PF0 15 P31/RxD0 DRxD 17 P33/TxD1/SCL1 P33 19 P35/SCK1/SCL0/IRQ P35 5 ...

Page 15

C D ODE EVELOPMENT 7.1. HMON 7.1. ODE UPPORT The HMON library is built to support Advanced Expanded Mode only. The Device supports Modes 6 and 7. 7.1. REAKPOINT UPPORT The monitor utilises the PC ...

Page 16

M M EMORY AP H'00000000 Vectors H'00001000 FDTInit H'00001119 H'00002000 CUser_Vectors H'00002003 H'00003000 PHMON CHMON H'00005615 On-Chip FLASH ROM H'0005F600 FDTUserModeMicr oKernel H'0005FE09 H'0005FFFF H'00200000 SRAM (when fitted) H'0027FFFF H'00FF7000 On-Chip RAM H'00FFB000 BHMON H'00FFB20E H'00FFEDB0 Stack H'00FFEFAF H'00FFEFBF ...

Page 17

AUD ATE ETTING HMON has initially set to connect at 115200Baud. Should the user wish to change this, the value for the BRR in HMONserialconfiguser.c will need to be changed and the project re-built. Please refer ...