EDK2282 Renesas Electronics America, EDK2282 Datasheet
EDK2282
Specifications of EDK2282
Related parts for EDK2282
EDK2282 Summary of contents
Page 1
... EDK2282 U M SER ANUAL F H8S/2282 FLASH M N CHIP ICROCONTROLLER ...
Page 2
Preface Cautions 1. This document may be, wholly or partially, subject to change without notice. 2. All rights reserved. No one is permitted to reproduce or duplicate, in any form, a part or this entire document without Hitachi Micro Systems ...
Page 3
T C ABLE OF ONTENTS ............................................................................................................................................. 3 ABLE OF ONTENTS ....................................................................................................................................... 4 TART UP NSTRUCTIONS 2.1. INSTALLING THE EVALUATION DEVELOPMENT KIT (EDK)........................................................................... 4 2.2. SERIAL CONNECTION ....................................................................................................................................... 4 2.3. POWER SUPPLY ................................................................................................................................................ ...
Page 4
TART UP NSTRUCTIONS 2. NSTALLING THE VALUATION Please refer to the quick start guide provided for initial installation of the EDK. A copy of the quick start guide and other information relating to this ...
Page 5
EDK B L OARD AYOUT The diagram shows a general layout of the EDK board. FLASH Programming Power NMI Switch BOOT LED Power LED User1 LED User2 LED RESET BOOT Switch Switch CJ5 9-Way D-Type CJ4 3.1. EDK B ...
Page 6
EDK O PERATION 4.1. USER INTERFACE The EDK provides three buttons for influencing the operation of the board. The purpose of each button is clearly marked next to it. Refer to the board layout for positions (Section 3) 1. ...
Page 7
C C RYSTAL HOICE The operating crystal frequency has been chosen to support the fastest operation with a 500k baud CAN data rate. The value of the crystal is 20MHz. This affects the maximum possible serial baud rate. The ...
Page 8
M M EMORY AP Table 4-4 illustrates the EDK memory map for mode 7. Section Start Section End H’000000 H’01FFFF H’020000 H’FFDFFF H’FFE000 H’FFEFBF H’FFEFC0 H’FFF7FF H’FFF800 H’FFFF3F H’FFFF40 H’FFFF5F H’FFFF60 H’FFFFBF H’FFFFC0 H’FFFFFF 4.5. LED S The EDK ...
Page 9
B O OARD PTIONS The EDK has a number of configuration settings set by jumpers CJ4 ( CJ5 ( and zero-ohm links. Common EDK functions can be set using the jumpers as described ...
Page 10
– CJ5 SER ODE ETTINGS CJ5 is used to set the operating mode of the microcontroller. These jumpers must be fitted at all times to ensure correct operation of the EDK. Jumper CJ 5-A User Mode ...
Page 11
... LCD The H8/2282 features a 28 segment LCD driver. Two different LCD footprints are to be provided on the EDK2282 PCB (only one in use at any one time): • VI-422-DPRC (direct drive 4 digits) (NORMALLY FITTED) • VI-503-DPRC-LV (multiplexed 4.5 digits) The H8S/2282 internal LCD controller is connected as follows: ...
Page 12
ERIAL ORT ELECTION The programming serial port is connected to the RS232 connector by default. This allows direct programming of the EDK using the supplied software tools. A secondary serial port is available on the microcontroller ...
Page 13
LASH ROGRAMMING EADER The Flash Programming header is used with the Hitachi Flash Debug Board (FDB). The FDB is a USB based programming tool for control and programming of Hitachi microcontrollers, available separately from Hitachi. This ...
Page 14
S D TATE IAGRAM Async Boot Mode Controller : Positive Logic (CTS+BootSw) . /Res Waiting Reset Timer /Res ResSw . /Res Res /Res . Reset Reset (BootSW + ResSw + CTS) . /Res F 5-2: CPLD S D IGURE ...
Page 15
M H ICROCONTROLLER EADER The following table lists the connections to each or the headers on the board. 6. EADER Pin Function EDK Symbol No 1 RESn RESn 3 VCL NC71 5 PLLCAP NC69 7 NMI NMIn ...
Page 16
C D ODE EVELOPMENT 7.1. HMON 7.1. ODE UPPORT The HMON library is built to support Advanced Mode only. The Device supports only Mode 7. 7.1. REAKPOINT UPPORT The monitor utilises the device RAM for ...
Page 17
M M EMORY AP H'00000000 H'00001000 H'0000111D H'00002000 H'00002003 H'00005000 H'000073F3 H'0001F600 H'0001FE4B H'0001FFFF H'00FFE000 H'00FFEB80 H'00FFED8E H'00FFEDC0 H'00FFEFAF H'00FFEFBF H'00FFF800 H'00FFFF3F H'00FFFF60 H'00FFFFC0 H'00FFFFFF Vectors FDTInit CUser_Vectors PHMON CHMON On-Chip FLASH ROM FDTUserModeMicr oKernel On-Chip RAM BHMON Stack ...
Page 18
AUD ATE ETTING HMON has initially set to connect at 57600 Baud. Should the user wish to change this, the value for the BRR in HMONserialconfiguser.c will need to be changed and the project re-built. Please ...