HS1527KEPH60H Renesas Electronics America, HS1527KEPH60H Datasheet
HS1527KEPH60H
Specifications of HS1527KEPH60H
Related parts for HS1527KEPH60H
HS1527KEPH60H Summary of contents
Page 1
To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...
Page 2
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...
Page 3
H8SX Family E10A Emulator Additional Document for User’s Manual H8SX/1527F E10A HS1527KCI01HE-U2 Renesas Microcomputer Development Environment System H8SX Family / H8SX/1500 Series Specific Guide for the H8SX/1527F, H8SX/1525F E10A Emulator Rev.1.00 2004.09 ...
Page 4
...
Page 5
Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead ...
Page 6
...
Page 7
Section 1 Connecting the Emulator with the User System ................................1 1.1 Components of the E10A Emulator .................................................................................. 1 1.2 Connecting the E10A Emulator with the User System ..................................................... 2 1.3 Pin Assignments of the E10A Connector.......................................................................... 4 1.4 Example of ...
Page 8
ii ...
Page 9
Section 1 Connecting the Emulator with the User System 1.1 Components of the E10A Emulator The H8SX/1527F E10A emulator supports the H8SX/1527F and H8SX/1525F (hereafter referred to as the MCU unless the description is specific to any of them). Table ...
Page 10
Connecting the E10A Emulator with the User System Before connecting an E10A emulator with the user system, a connector must be installed in the user system so that an user system interface cable can be connected. When designing the ...
Page 11
Be sure to place the GND line of the user system interface cable on the GND of the user system with a screw, etc. Failure will result in a FIRE HAZARD due to an overcurrent and will ...
Page 12
Pin Assignments of the E10A Connector Figure 1.2 shows the pin assignments of the user system connector. Pin 1 mark User system connector Pin 8 Pin 1 Top view Pin 1 mark Figure 1.2 Pin Assignments of the User ...
Page 13
Example of Emulator Connection The figure shown below is an example of connecting the user system to the emulator. 14-pin connector with a 2.54-mm pitch (3M Limited: 2514-6002 ...
Page 14
Notes: 1. P34/TRST#, P37/TCK, P35/TMS, P63/TDO, and P36/TDI are used by the emulator. Pull up and connect the emulator and the MCU pins. User system connector Pins and 6 Figure 1.4 Connection of Emulator and MCU ...
Page 15
RES(in)# of pin 4 of the user system connector is a signal line in which the emulator outputs signals to the MCU. RES(in)# of pin 4 and the user logic reset circuit for the signal line must be connected ...
Page 16
Figure 1.7 shows the interface circuit in the emulator. Use this figure as a reference to decide the pull-up resistance value. Emulator control circuit HD74LV125A Vcc 3.3 V HD74LVTH244 Vcc Figure 1.7 Interface Circuit in the Emulator (Reference) 7. ...
Page 17
Section 2 Specification of the E10A Emulator’s Software 2.1 Differences between the H8SX/1527F or H8SX/1525F and the E10A Emulator 1. When the E10A emulator system is initiated, it initializes the general registers and part of the control registers as shown ...
Page 18
If the flash memory is reprogrammed many times, the data will not be erased error message is displayed, exchange the MCU for a new one. 7. MCU Operating Mode Use the E10A emulator in mode 3 (single-chip mode). ...
Page 19
The H8SX/1527F E10A Emulator Functions Notes not use an MCU that has been used for debugging the flash memory is reprogrammed many times, and the E10A emulator is left for a few days, data may ...
Page 20
Hardware Break Functions Hardware Break Conditions: In the H8SX/1527F E10A emulator, conditions of Break Condition 1,2,3,4 can be set. Table 2.3 lists the items that can be specified. Table 2.3 Hardware Break Condition Specification Items Items Address bus condition ...
Page 21
Table 2.5 lists the combinations of conditions that can be set by the BREAKCONDITION_SET command. Table 2.5 Conditions Set by BREAKCONDITION_SET Command Condition Address Bus Condition (option Channel <addropt>) O Break condition 1 O Break condition 2 O Break condition ...
Page 22
Notes on Setting the [Breakpoint] Dialog Box 1. When an odd address is set, the address is rounded down to an even address BREAKPOINT is accomplished by replacing instructions. Accordingly, it can be set only to the ...
Page 23
Note on Using the JTAG Clock (TCK) When the JTAG clock (TCK) is used, set the frequency to lower than that of the system clock. 2.2.6 Trace Function The trace function in the H8SX/1527F E10A emulator uses the eight-branch-instruction ...
Page 24
16 ...
Page 25
H8SX Family E10A Emulator Additional Document for User's Manual Specific Guide for the H8SX/1527F, H8SX/1525F E10A Emulator Publication Date: Rev.1.00, September 13, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas ...
Page 26
RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, ...
Page 27
H8SX Family E10A Emulator Additional Document for User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10B0148-0100H ...