CABLE-SMBUS-5PIN Analog Devices Inc, CABLE-SMBUS-5PIN Datasheet

CABLE-SMBUS-5PIN

Manufacturer Part Number

CABLE-SMBUS-5PIN

Description

CABLE SMBUS 5PIN

Manufacturer

Analog Devices Inc

Datasheet

1.USB-5PSMBUS-CABLEZ.pdf (20 pages)

Specifications of CABLE-SMBUS-5PIN

Accessory Type

SMBus Cable

For Use With/related Products

EVALADM106x Boards

Lead Free Status / RoHS Status

Contains lead / RoHS non-compliant

Current page: 1 of 20
Download datasheet (2Mb)

PRODUCT DESCRIPTION

This evaluation board allows the ADM1175/ADM1176/

ADM1177/ADM1178 devices to be easily evaluated. These

parts combine a hot swap controller and an on-board 12-bit

ADC-based digital power monitor that reports the power being

drawn. The hot swap control circuitry allows the boards to be

safely inserted and removed from a live 3.15 V to 16.5 V back-

plane. The parts provide precise, robust, current-limiting

protection against transient and nontransient short circuits

and undervoltage and overcurrent conditions. In addition

to the standard hot swap functionality, the on-board power

monitoring circuitry allows for precise monitoring of the

power profile of each individual line card within a designated

rack system. Communication to the power monitor is via an

on-board I

Order codes for evaluation kits are shown in the Ordering

Guide. (Pinouts and detailed package drawings can be found in

the individual product data sheets).

Rev. 0

Evaluation boards are only intended for device evaluation and not for production purposes.

Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or

statutory including, but not limited to, any implied warranty of merchantability or fitness for a

particular purpose. No license is granted by implication or otherwise under any patents or other

intellectual property by application or use of evaluation boards. Information furnished by Analog

Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use, nor for any infringements of patents or other rights of third parties that may result

from its use. Analog Devices reserves the right to change devices or specifications at any time

without notice. Trademarks and registered trademarks are the property of their respective owners.

Evaluation boards are not authorized to be used in life support devices or systems.

C® port.

DIGITAL PICTURE OF THE EVALUATION BOARD

5-PIN SMBus CABLE (J7)

GND (J4)

VIN (J3)

EVAL-ADM1175/ADM1176/ADM1177/ADM1178

ADM1175/ADM1176/ADM1177/ADM1178

MINIMOLEX CABLE (J8)

Figure 1.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

Fax: 781.461.3113

GENERAL DESCRIPTION

The ADM1175/ADM1176/ADM1177/ADM1178 hot swap

controller and digital power monitor evaluation board can

be controlled by the configuration tool allowing the device

to be actively stimulated through software. This board

requires a bench power supply of between 3.15 V and

16.5 V, connected through J3 and J4. Download the latest

version of the configuration tool from Analog Devices, Inc.,

at www.analog.com/powermonitorsw.

Note that when changing devices the software should first be

shutdown and the power supply to the board removed. J7 is an

a 5-pin SMBus cable.

PACKAGE CONTENTS

ADM1175/ADM1176/ADM1177/ADM1178 evaluation board

5-pin SMBus cable

5-pin ADM1175-92 interconnection cable

ADM1175/ADM1176/ADM1177/ADM1178 device samples

C connector that connects the PC to the evaluation board via

Evaluation Kit for the

www.analog.com

Related parts for CABLE-SMBUS-5PIN

CABLE-SMBUS-5PIN Summary of contents

Page 1

... SMBus cable 5-pin ADM1175-92 interconnection cable ADM1175/ADM1176/ADM1177/ADM1178 device samples DIGITAL PICTURE OF THE EVALUATION BOARD MINIMOLEX CABLE (J8) VIN (J3) GND (J4) 5-PIN SMBus CABLE (J7) Figure 1. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 Evaluation Kit for the www.analog.com ...

Page 2

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 TABLE OF CONTENTS Product Description ......................................................................... 1 General Description ......................................................................... 1 Package Contents .............................................................................. 1 Digital Picture of the Evaluation Board ......................................... 1 Revision History ............................................................................... 2 Evaluation Board Hardware ............................................................ 3 Hardware Components ................................................................ 3 Switch Functions .......................................................................... ...

Page 3

... It also has an adjustable load circuit to evaluate the performance of the device under varying load conditions. 5-Pin SMBus Cable This cable connects the main evaluation board to a standard PC via J7. 5-Pin Interconnection Cable This cable is used for multiple evaluation board parallel connec- tion setups ...

Page 4

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 Switch Description S6 Applies only to the ADM1175 device. Controls the CONV pin, when depressed the CONV pin is high. For Switch S6 to control the CONV pin, the jumper in Link 3 should be in Position B (separate ...

Page 5

... C interface Communication between a PC and the evaluation board is achieved through the 5-pin header (J7), which should command. connected to the PC using the provided cable. CONFIGURATION TOOL The configuration tool enables the user to program and 2 C addresses can be monitor the many features of the hot swap controllers, power monitors, and current-sense amplifiers through an intuitive, GUI-based interface ...

Page 6

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 INSTALLING THE EVALUATION SOFTWARE Install the software using the following steps: 1. Download the .zip file containing the software from the website: www.analog.com/powermonitorsw. 2. Extract the files from the .zip file. 3. Double-click setup.exe. The Installation Wizard window appears ...

Page 7

Upon completion, the following window appears: Figure 7. Evaluation Software—Installation Complete 8. Click Finish. The Installer Information window appears indicating that you should restart the system for the confi- guration changes to take effect (see Figure 8 ...

Page 8

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 USB–COMMUNICATING FOR THE FIRST TIME When the board is launched for the first time using a USB connection, Windows does not recognize the external evaluation board and begins installing drivers automatically. The Found New Hardware Wizard window appears (see ...

Page 9

LAUNCHING THE EVALUATION SOFTWARE 1. To launch the evaluation software, click Start\All Programs\ ADM1175-92 Configuration Tool 3.0.1\ADM1175-92 Configuration Tool 3.0.1. Note that the actual folder name is version dependent. 2. Once launched, the Evaluation Software Agreement window appears (see Figure ...

Page 10

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 EVALUATION SOFTWARE—MAIN PANEL TAB The Main Panel tab of the evaluation software is shown in Figure 17. Each aspect of the main panel is discussed in detail in the following sections. Figure 17. Main Panel on User Interface COMMAND ...

Page 11

STATUS REGISTER CONTROLS Figure 21. Status Register Panel The Status Register monitors three alert types: ADC overcurrent alert, hot swap overcurrent alert, and software off alert. The Status Register has six alert indicators. The upper row shows the real-time alert ...

Page 12

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 DATA LOGGER CONTROLS Figure 27. Data Logger Panel The Data Logger panel allows you to log the digitized data collected in a Microsoft® Excel file, giving you more flexibility to monitor and compare data. However, you must set up ...

Page 13

REAL-TIME GRAPHS OF VOLTAGE, CURRENT, AND POWER Figure 32. Panel Selection Tabs The tabs located on the top of the user interface allow you to switch between the Main Panel and the voltage, current, and power graphs. You can monitor ...

Page 14

... V and 16.5 V, connected to J3 (VIN) and J4 (GND). The first evaluation board should be connected to the PC using a 5-pin SMBus cable from the 5-pin header labeled J7. Each board is fitted with two MiniMolex® interconnecters, J8 and J9. To interconnect multiple boards use the provided red 5-pin MiniMolex cables ...

Page 15

The digitized values for voltage, current, and power are displayed in the control panel on the left (see Figure 43). Select which traces to view by clicking the check box to the left of each trace name. You can also ...

Page 16

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 EVALUATION BOARD SCHEMATIC Figure 49. ADM1175/ADM1176/ADM1177/ADM1178 Evaluation Board Schematic Rev Page 06474-049 ...

Page 17

ORDERING INFORMATION BILL OF MATERIALS Table 5. Reference Qty Designator Description 1 C1 4.7 nF, 10%, 0805 multilayer ceramic capacitor, SMD 2 C2, C11 47 nF, 10%, 0805 multilayer ceramic capacitor, SMD 1 C3 470 nF, 10%, 0805 multilayer ceramic ...

Page 18

... Model Description EVAL-ADM1175EBZ 1 Evaluation Board 1 EVAL-ADM1176EBZ Evaluation Board EVAL-ADM1177EBZ 1 Evaluation Board 1 EVAL-ADM1178EBZ Evaluation Board 1 CABLE-SMBUS-5PINZ 5-Pin SMBus Cable (Parallel Port) 1 USB-5PSMBUS-CABLEZ 5-Pin SMBus Cable (USB Port RoHS Compliant Part. Manufacturer Manufacturer Number Multicomp MC 0.1W 0805 1% 10R Phycomp 232276260108 Multicomp MC 0.1W 0805 1% 4K7 ...

Page 19

NOTES EVAL-ADM1175/ADM1176/ADM1177/ADM1178 Rev Page ...

Page 20

EVAL-ADM1175/ADM1176/ADM1177/ADM1178 NOTES ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. EB06474-0-5/08(0) Rev Page ...

Related keywords

CABLE-SMBUS-5PIN datasheet
CABLE-SMBUS-5PIN data sheet
CABLE-SMBUS-5PIN pdf datasheet
CABLE-SMBUS-5PIN component
CABLE-SMBUS-5PIN part
CABLE-SMBUS-5PIN distributor
CABLE-SMBUS-5PIN RoHS
CABLE-SMBUS-5PIN datasheet download