SKPCOMMS Renesas Electronics America, SKPCOMMS Datasheet
SKPCOMMS
Specifications of SKPCOMMS
Related parts for SKPCOMMS
SKPCOMMS Summary of contents
Page 1
... KPCOMMS www.renesas.com SKPCOMMS User’s Manual Rev. 1.0 Preliminary USERS MANUAL Ver. 1.0 Rev. 1.0 July 2004 Applications Engineering June 2004 ...
Page 2
... Limited Guarantee and Support .................................................................................... 4 4.0 System Connectivity ..................................................................................................... 5 5.0 Hardware....................................................................................................................... 7 6.0 System Operation & Limitations ................................................................................ 11 7.0 SKPCOMMS Board Specifications............................................................................ 12 Appendix A. Troubleshooting Guide................................................................................ 13 Appendix B. Reference Manuals ...................................................................................... 13 Appendix C. Expansion Headers ...................................................................................... 14 Appendix D. SKP Board Dimensions............................................................................... 15 Appendix E. RTA-FoUSB-MON (ICD)........................................................................... 16 SKPCOMMS User’s Manual Rev. 1.0 Applications Engineering June 2004 ...
Page 3
... It was design to bring out various communication interfaces from SKP MCUs as well as provide more functionality, such as an external power supply, than what standard SKP board. The SKPCOMMS board can be ordered fully populated, or with a sub-set of components. SKPCOMMS User’s Manual Rev. 1.0 Applications Engineering ...
Page 4
... Contents of Product Package This section describes the contents of the SKPCOMMS product package. When unpacking your SKPCOMMS, please check to see that all products listed below are included. 2.1 SKPCOMMS StarterKit Plus Add-on Product List Table 2-1 lists the products included in the SKPCOMMS. ...
Page 5
... Limited Guarantee and Support Renesas Technology America, Inc., warrants the SKPCOMMS to be free from component or assembly defect for a period of 180 days from the date of purchase. Settlement is limited to repair or replacement of the product only. Renesas Technology America, Inc., does not assume any liability arising out of the application or use of any product, circuit or procedure described herein ...
Page 6
... System Connectivity The following lists the hardware and software products required for using the SKPCOMMS StarterKit Plus Add-on. • Host Computer (supplied by user) • Standard Renesas SKP board (sold separately) • SKPCOMMS Board • (2) Dual row 50-pin headers (to be populated on the board by user) • ...
Page 7
... The minimum requirement to be able to use the software that comes with the SKPCOMMS with a USB port and Microsoft Windows 98, ME, 2000, or XP. Note: For Windows 95 and NT, that do not support USB, please contact Renesas representative or email techsupport.rta@renesas.com 4.2 SKPCOMMS Board The SKPCOMMS board is an Add-on board for standard Renesas SKP boards designed to be plugged standard SKP evaluation product ...
Page 8
... Hardware 5.1 SKPCOMMS Board Figure 5-1 shows the SKPCOMMS Board with major components identified. Figure 5-1. SKPCOMMS Board Vcc Test Point External Power input SRAM Chip Connection headers for SKP8CMINI CAN Ports SKPCOMMS User’s Manual Rev. 1.0 Applications Engineering ...
Page 9
... SKPCOMMS Board Block Diagram The SKPCOMMS board contains multiple component interfaces. Note that not all components may be populated depending on which version you purchased. Figure 5-2. SKPCOMMS Block Diagram Vcc Power Supply 12MHz Ethernet Address 10/100 16-bit Data LAN96C111 RD WR INTR ...
Page 10
... SKPCOMMS Board Jumper Configuration 5.4.1 Table of Jumper Connections The following table shows all the jumper settings for the SKPCOMMS board. Note that the default jumper settings are different for a full SKPCOMMS board (all components populated) as opposed to a COMMS-LITE (Ethernet and SRAM not populated). ...
Page 11
... NOTE 1 - The chip select order is reversed between the M16C and M32C family of devices. The silk screen on the SKPCOMMS board is for M16C. So for M32C, you would short the position for CS3 if you desired CS0. NOTE 2 – Setting up the variable power supply is beyond the scope of this manual. Contact your local Renesas representative for assistance. SKPCOMMS User’ ...
Page 12
... Target M16C ROM Monitor Resources or related ICD application notes. 6.3 Memory Map Because the SKPCOMMS board was designed to work will all the standard SKP kits, the memory map for address mapped components (SRAM and Ethernet) will be different for each device depending on the chip select jumpers used. Refer to the MCU’s hardware manual for more details. SKPCOMMS User’ ...
Page 13
... RTA-FoUSB-MON debugger. Therefore, only use the provided external power supply to power your system. 7.3 Operating Environment Table 7-3 lists the environmental conditions for using and storing the SKPCOMMS board. When storing the board, place conductive bag and then in the packing box your product was shipped in from the factory. ...
Page 14
... This section discusses how to install the SKPCOMMS software and development tools manually (i.e. when not using the SKPCOMMS installer). (1) Create an SKPCOMMS folder under C:\MTOOL on your PC and then copy the directories from the \SKPCOMMS\files folder on the SKP CD to this folder. Appendix B. Reference Manuals ...
Page 15
... P7_2, CLK2, TA1out P7_4, TA2out P7_6, TA3out 19 P6_0, CTS0 20 P6_2, RxD0, SCL0 21 P6_4, CTS1, CLKS1 22 P6_6, RxD1, SCL1 23 Vref 24 Vcc 25 Vcc SKPCOMMS User’s Manual Rev. 1.0 Applications Engineering J2 Pin Function 1 GND 2 P0_1, AN01 P0_3, AN03 P0_5, AN05 P0_7, AN07 P1_1 P1_3, D11 8 ...
Page 16
... Appendix D. SKPCOMMS Board Dimensions .100” .100” 3.200” NOTES: • All headers are standard 0.1 inch spacing • Distance between headers are the same for top and bottom side of the board SKPCOMMS User’s Manual Rev. 1.0 Applications Engineering June 2004 ...
Page 17
... Appendix E. RTA-FoUSB-MON (ICD) For details on how to use the ICD, please see RTA-FoUSB-MON user’s manual. SKPCOMMS User’s Manual Rev. 1.0 Applications Engineering June 2004 ...