HL1-HP-AC12V Panasonic Electric Works, HL1-HP-AC12V Datasheet - Page 3

• Manufacturer Part Number: HL1-HP-AC12V
• Description: RELAY POWER 15A 12VAC PCB
• Manufacturer: Panasonic Electric Works
• Series: HLr

Specifications of HL1-HP-AC12V

• Relay Type: General Purpose
• Contact Form: SPDT (1 Form C)
• Contact Rating (current): 15A
• Switching Voltage: 125VAC
• Coil Type: Standard
• Coil Current: 100mA
• Coil Voltage: 12VAC
• Turn On Voltage (max): 9.6 VAC
• Turn Off Voltage (min): 3.6 VAC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Circuit: SPDT (1 Form C)
• Contact Rating @ Voltage: 15A @ 125VAC
• Control On Voltage (max): 9.6 VAC
• Control Off Voltage (min): 3.6 VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

RATING
1. Coil data
1) AC coils
Notes: 1. The relay operates in a range of 80% to 110% V of the voltage rating, but ideally, in consideration of temporary voltage fluctuations, it should be operated at the
2) DC coils (at 20°C 68°F)
Notes: 1. The rated excitation current is ±10% (20°C 68°F).
2. Specifications
Notes: If integrating into electrical appliances that will be subject to compliance to the Electrical Appliance and Material Safety Law, please use in an ambient temperature
Contact
Rating
Electrical
characteristics
Mechanical
characteristics
Expected life
Conditions
Unit weight
100/110V DC
100/110V AC
110/120V AC
200/220V AC
Characteristics
Nominal coil
Nominal coil
12V AC
24V AC
48V AC
12V DC
24V DC
48V DC
voltage
voltage
6V AC
6V DC
2. The maximum allowable voltage is the maximum voltage fluctuation value for the coil power supply. This value is not a permissible value for continuous operation.
2. The coil resistance for DC operation is the value measured when the coil temperature is 20°C 68°F. Compensate ±0.4% for every ±1°C change in temperature.
3. The relay operates in a range of 80% to 110% V of the voltage rating, but ideally, in consideration of temporary voltage fluctuations, it should be operated at the
4. For use with 200 V DC, connect a 10 KΩ (5W) resistor, in series, to the 100 V DC relay.
5. The maximum allowable voltage is the maximum voltage fluctuation value for the coil power supply. This value is not a permissible value for continuous operation.
*1 This value can change due to the switching frequency, environmental conditions and desired reliability level, therefore it is recommended to check this with the
*2 For the AC coil types, the operate/release time will differ depending on the phase.
*3 The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value.Refer to 4. Conditions for operation,
rated voltage.
In particular, for AC operation, if the applied voltage drops to 80% V or more below the rated voltage, humming will occur and a large current will flow leading possibly
to coil burnout.
(This value differs depending on the ambient temperature. Please contact us for details.
rated voltage.
(This value differs depending on the ambient temperature. Please contact us for details.)
between –50°C to +40°C
actual load.
transport and storage mentioned in AMBIENT ENVIRONMENT.
13.4/14.7
12.2/13.5
Nominal coil current
Initial contact resistance, max
Contact material
Nominal switching capacity
Min. switching capacity (Reference value)*
Insulation resistance (Initial)
Breakdown voltage
(Initial)
Temperature rise
Operate time (at 20°C 68°F)*2
Release time (at 20°C 68°F)*2
Shock resistance
Vibration resistance
Mechanical
Electrical
Conditions for operation, transport and storage*
Max. Operating speed
6.7/7.4
Nominal coil current
50Hz
224
111
56
28
(mA)
18.5
150
75
37
10
(mA)
10.9/11.9
12/13.2
60Hz
6/6.6
–58°F to +104°F
200
100
50
25
Between open contacts
Between contact sets
Between contact and coil
Functional
Destructive
Functional
Destructive
AC load
DC load
Item
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd.
Nominal operating
Nominal operating power
50Hz
power (W)
1.3
1.3
1.3
1.3
1.3
1.3
1.3
(AC type).
0.9
0.9
0.9
0.9
1.0
(VA)
1
60Hz
1.2
1.2
1.2
1.2
1.2
1.2
1.2
3
Max. 50 mΩ (By voltage drop 6 V DC 1A)
AgSnO
1 Form C: 15A 125V AC, 10A 250V AC (resistive load)
2 Form C: 10A 125V AC (resistive load)
100mA 5V DC
Min. 100MΩ (at 500V DC)
Measurement at same location as “Initial breakdown voltage” section.
1,000 Vrms for 1min. (Detection current: 10mA.)
1,500 Vrms for 1min. (Detection current: 10mA.)
2,000 Vrms for 1min. (Detection current: 10mA.)
Max. 80°C (By resistive method, nominal voltage)
DC type/AC type: Max. 25ms (Nominal voltage applied to the coil, excluding contact bounce time.)
DC type/AC type: Max. 25ms (Nominal voltage applied to the coil, excluding contact bounce time.)
(without diode)
Min. 196 m/s
Min. 980 m/s
10 to 55 Hz at double amplitude of 1 mm (Detection time: 10µs.)
10 to 55 Hz at double amplitude of 2 mm
AC type: 5×10
1 Form C: 15A 125V AC, 10A 250V AC resistive load (cosϕ=1) Life switching cycle: Min. 5×10
2 Form C: 10A 250V AC resistive load (cosϕ=1) Life switching cycle: Min. 3×10
1 Form C: 3A 30V DC resistive load (cosϕ=1) Life switching cycle: Min. 5×10
2 Form C: 3A 30V DC resistive load (cosϕ=1) Life switching cycle: Min. 5×10
Ambient temperature: –50°C to +70°C
–50°C to +60°C
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
20 cpm (at max. rating)
Approx. 35g
Coil resistance
80%V or less of
nominal voltage
Pick-up voltage
(at 20°C 68°F)
10,000
2,600
2
160
650
(Ω)
type
40
(Initial)
1.23 oz
2
2
7
(Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)
(Half-wave pulse of sine wave: 6 ms.)
(at 180 cpm), DC type: 10
–58°F to +140°F
Drop-out voltage
30%V or more of
nominal voltage
(at 20°C 68°F)
80%V or less of
nominal voltage
Pick-up voltage
(at 20°C 68°F)
(Initial)
(Initial)
(With LED indication)
–58°F to +158°F
8
Specifications
(at 180 cpm)
When drop-out
0.078
0.312
1.243
4.974
23.75
27.19
85.98
10%V or more of
Drop-out voltage
nominal voltage
Inductance (H)
(at 20°C 68°F)
(Without LED indication);
(Initial)
When operating
0.074
0.295
1.181
4.145
20.63
25.57
81.76
Max. allowable voltage
5
5
5
(at 70°C 158°F)
nominal voltage
nominal voltage
110%V of
Max. allowable
110%V of
voltage
HL
5