ZX-XF12 Omron, ZX-XF12 Datasheet
ZX-XF12
Specifications of ZX-XF12
Related parts for ZX-XF12
ZX-XF12 Summary of contents
Page 1
... Smart Sensors (Laser Type) ZX Series (ZX-L-N) Ordering Information ■ Sensors Sensor Heads (Reflective) Optical system Beam shape Diffuse reflective Spot beam Line beam Regular reflective Spot beam Line beam *1. For an average count of 4,096. Sensor Heads (Through-beam) Optical system Measuring width Through-beam 1-mm dia ...
Page 2
... Function Setting Soft- ware) ZX Series (ZX-L-N) 2 Setup Tool for Personal Computer Model Appearance Note 1. The ZX-SFW11EV3 or ZX-SW11EV3 is required to use the 2. The Smart Monitor Basic does not have a logging function. Model Quantity ZX-XF12 1 Cables with Connectors on Both Ends (for Extension)*1 ZX-XF22 Cable length Model ZX-SF11 *1 ...
Page 3
... Resolution: The resolution is the deviation (±3σ) in the linear output when connected to the ZX-LDA Amplifier Unit. (The resolution is measured with the standard reference object (white ceramic), at the measurement point with the ZX-LDA set for an average count of 4,096 per period.) The resolution is given at the repeat accuracy for a stationary workpiece, and is not an indication of the distance accuracy ...
Page 4
... This is the value that results when a minimum sensing object blocks the light near the center of the 1-mm measurement width. *3. For an average count of 64. The value is 5 µm for an average count of 32. *4. For an average count of 64. The value is 15 µm for an average count of 32. ZX Series (ZX-L-N) 4 ZX-LT005 ...
Page 5
... The response speed of the judgement outputs is calculated as the measurement period *2. The output can be switched between a current output and voltage output using a switch on the bottom of the Amplifier Unit. *3. Setting is possible via the monitor focus function. *4. A Calculating Unit (ZX-CAL2) is required. ZX-LDA11 times each in six directions (up/down, left/right, forward/backward) × ...
Page 6
... Display: Acrylic, Case: ABS resin Approx max. (supplied by the Amplifier Unit) ZX Series ZX-LDA@1-N Ver. 1.000 or higher ZX-EDA@1 Ver. 1.100 or higher ZX-TDA@1 Ver. 1.000 or higher 5 RS-232C port (9-pin D-Sub Connector) CompoWay/F* 38,400 bps Data bits: 8, Parity: none, Start bits: 1, Stop bits: 1, Flow control: none ...
Page 7
... Black paper + inclination 2 − inclination 1 0 −1 −2 −3 −4 −10 −8 −6 −4 − Angle of inclination (°) ZX Series (ZX-L-N) ● ZX-LD300 Side-to-side Inclination 20 White ceramic SUS304 15 Black paper −5 −10 + inclination −15 − inclination −20 −10 −8 −6 −4 −2 ...
Page 8
... Black paper + inclination 2 − inclination 1 0 −1 −2 −3 −4 −10 −8 −6 −4 − Angle of inclination (°) ZX Series (ZX-L-N) 8 ● ZX-LD30VL Side-to-side Inclination 4 White ceramic SUS304 3 Black paper + inclination 2 − inclination 1 0 −1 −2 − 3 −4 −10 −8 −6 −4 − ...
Page 9
... Distance (mm) −10° Inclination Front-to-back 4 White ceramic SUS304 3 Black paper −1 −2 −3 −10° inclination − Distance (mm) ZX Series (ZX-L-N) 10° Inclination 4 White ceramic SUS304 3 Black paper 2 10° inclination 1 0 −1 −2 −3 − Distance (mm) 10° Inclination 4 ...
Page 10
... Black paper 0.6 0.4 0.2 0 −0.2 −0.4 −0.6 −0.8 0° inclination −1.0 28.0 28.4 28.8 29.2 29.6 30.0 30.4 30.8 31.2 31.6 32.0 Distance (mm) ZX Series (ZX-L-N) 10 −10° Inclination Front-to-back 4 White ceramic SUS304 3 Black paper 2 −10° inclination 1 0 −1 − ...
Page 11
... ZX-LD30VL 2,000 µm 250 µm 140 mm 2,000 µm 430 µm 500 mm 2,500 µm 650 µm ZX Series (ZX-L-N) L Beam cross-section 60.0 µm 30.0 µm 120 µm 50.0 µm 40.0 µm 90.0 µm L Beam cross-section 1,800 µ ...
Page 12
... WD=450 mm Sensing distance: 500 −1 −2 Receiver Emitter side side −3 WD − Light interruption (mm) ZX Series (ZX-L-N) 12 ● ZX-LT001 (For 0.05-mm-dia. pin gauge −2 −4 −6 WD=200 mm −8 WD=500 mm WD=1,000 mm −10 WD=1,500 mm WD=1,800 mm −12 Sensing distance Sensing object: 0.05-mm dia. −14 ...
Page 13
... Voltage Output Linear output ( 100 120 140 160 Distance (mm) −2 −4 −6 Voltage Output Linear output ( 100 200 300 400 500 600 Distance (mm) −2 −4 −6 Voltage Output Measurement range (4 mm Distance (mm) −2 −4 −6 ZX Series (ZX-L-N) Smart Sensors (Laser Type) 13 ...
Page 14
... I/O Circuit Diagrams NPN Amplifier Unit: ZX-LDA11-N Brown VDC White: HIGH output Green: PASS output Gray: LOW output Blue: GND (0V) Pink: Laser OFF input Purple: Timing input Orange: Zero reset input Red: Reset input Current output Current/voltage Black: Linear output switch Voltage output ± ...
Page 15
... Amplifier Units ZX-LDA11-N ZX-LDA41-N Display area Input cable (with connector) Calculating Unit ZX-CAL2 Emitter Light emitter Receiver side (Optical filter) Receiver ZX Series (ZX-L-N) Controls Display area Output cable Connector (Cover opens and closes.) Display area Connector Smart Sensors (Laser Type) 15 ...
Page 16
... Sensor. Use a shielded cable to extend the Amplifier cable. The shielded cable must be the same as that of the Amplifier cable. • Do not lay a power supply cable for the ZX together with high-volt- age lines or power lines to prevent interference, damage, and mal- function. ...
Page 17
... The ZX-LD-Series Sensor Heads are FDA Class II and EN Class 2 Laser Products. The ZX-LT-Series Sensor Heads are FDA Class II and EN Class 1 Laser Products. The ZX Series is meant to be built into final system equipment. Pay special attention to the following precautions for the safe use of the product: Note: Europe: Class 1 and Class 2 of EN60825-1: 1994 = IEC825-1: 1993 U ...
Page 18
... AEL: Accessible Emission Limit The maximum accessible emission level permitted within a particular class. For your reference, see ANSI Z136.1-1993, Section 2. ZX Series (ZX-L-N) 18 Symbol and border: black Background: yellow Figure A Warning label - Hazard symbol Legend and border: black Background: yellow Figure B Explanatory label ...
Page 19
... N/A N (see note (see note 5) (see note 5) (see note 5) N (see note 6) (see note 7) (see note Series (ZX-L-N) IIIa IIIb (see note 2) (see note (see note 10) (see note 10 N/A R (see note 13 (see note 8) (see note (see note 11) (see note 11 (see note 5) ...
Page 20
... Area Posting (4.3.15) Administrative & Procedural Controls Standard Operating Procedures (4.4.1) Output Emission Limitations (4.4.2) Education and Training (4.4.3) Authorized Personnel (4.4.4) Alignment Procedures (4.4.5) ZX Series (ZX-L-N) 20 Classification Class 2 Class 3A Terminate beam at end of useful length Required if engineering and administrative procedures not practicable ...
Page 21
... MPE MPE MPE MPE ✝ --- X MPE MPE MPE --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- Use may be required --- • LSO Determination LSO Determination Description ZX Series (ZX-L-N) Smart Sensors (Laser Type) --- • X --- • X ✩ MPE MPE X X --- X X NHZ NHZ --- • X MPE MPE --- X X NHZ NHZ --- • ...
Page 22
... Certification and Caution identification label logo type Aperture label Note: Use of controls, adjustments, or procedures other than those specified herein may result in hazardous radiation exposure. ZX Series (ZX-L-N) 22 FDA definition EN/IEC warning label Laser warning label Explanatory label with specified wording Aperture Label ...
Page 23
... A ∗ 30.05 32 Receiver axis Range 39 indicators 7 3.5 7 24.05 Connector 26 15 dia. 46 Vinyl-insulated round cable, 5.1 dia., Standard: 500 mm ∗ ZX-LD40L mm 23° ZX-LD10L 100 mm 11° ZX-LD30L 300 mm 3.8° 14 4.8 25 8.6 5-R2 42.7 45 32.7 4.75 4.75 35° 30 Emitter Receiver axis ...
Page 24
... Sensor Head-Amplifier Unit Connecting Cable (Provided) +200 1,500 0 2.6 dia × 2 Connector ZX Series (ZX-L- Light axis center Light axis center 15 Slit ( (Only for ZX-LT005) Mounting Holes 9± 0.1 Two, M3 holes 46 15 dia. Connector Light axis center Light axis center 20 14± 0.1 ...
Page 25
... Lens (8 x 36) Slit (1 x 30) Two + dia. 133 44 4.2 64 36.8 11.7 2.2 29 Current/voltage output selector switch (set to voltage output when shipped) ZX Series (ZX-L-N) Receiver 22.6 Vinyl insulated round 1 52 cable, 4 dia., Three Standard length: 0 pan head screw Connector 10 ...
Page 26
... Accessories (Order Separately) Calculating Unit ZX-CAL2 15 Side-view Attachments ZX-XF12 15 ZX-XF22 Two, 2.2 dia Series (ZX-L-N) 26 Operation 24.9 indicators 3 19.5 57 54.9 44.05 9 14.4 5 36.7 3.4 15 Light axis center Two, 2.2 dia. 10 2.7 20 Light axis center 21 Seal 20 2.8 Smart Sensors (Laser Type) ...
Page 27
... ZX-series Communications Interface Unit ZX-SF11 Sensor communications indicator (communications operation) Sensor communications indicator (communications error) 30 (46) 15 13.2 Vinyl-insulated round cable, 5.23 dia. Standard: 100 mm (33.1) Connector Cables with Connectors on Both Ends (for Extension) 46 ZX-XC1A (1 m) ZX-XC4A ( dia. ZX-XC8A (8 m) ZX-XC9A (9 m) ...
Page 28
... This document provides information mainly for selecting suitable models. Please read the document Z197 carefully for information that the user must understand and accept before purchase, including information on warranty, limitations of liability, and precautions. In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company Sensing Devices Division H.Q. Application Sensors Division ...
Page 29
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specifi ed) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...