MC74HC595A Motorola, MC74HC595A Datasheet
MC74HC595A
Available stocks
Related parts for MC74HC595A
MC74HC595A Summary of contents
Page 1
... The shift register and latch have independent clock inputs. This device also has an asynchronous reset for the shift register. The HC595A directly interfaces with the Motorola SPI serial data port on CMOS MPUs and MCUs. Output Drive Capability: 15 LSTTL Loads Outputs Directly Interface to CMOS, NMOS, and TTL Operating Voltage Range: 2 ...
Page 2
... SOIC Package: – from 125 _ C TSSOP Package: – 6.1 mW from 125 _ C For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). RECOMMENDED OPERATING CONDITIONS Î Î Î Î ...
Page 3
... Current (per Package) Î Î Î Î Î Î Î Î Î Î Î Î Î NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D). AC ELECTRICAL CHARACTERISTICS Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î Î ...
Page 4
... High–Impedance State – NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the Motorola High– Î Î Î Î ...
Page 5
... Noninverted, Serial Data Output. This is the output of the eighth stage of the 8–bit shift register. This output does not have three–state capability. 5 MC54/74HC595A Resulting Function Latch Serial Parallel Register Output Outputs Contents – Enabled ** * Z MOTOROLA ...
Page 6
... Figure 3. VALID SERIAL 50% INPUT LATCH 50% CLOCK Figure 5. TEST POINT OUTPUT DEVICE UNDER TEST * Includes all probe and jig capacitance Figure 7. MOTOROLA SWITCHING WAVEFORMS V CC RESET GND t PHL OUTPUT SQ H SHIFT CLOCK OUTPUT V CC 50% ENABLE GND OUTPUT Q OUTPUT Q SHIFT CLOCK ...
Page 7
... MC54/74HC595A PARALLEL DATA OUTPUTS SERIAL 9 DATA OUTPUT SQ H MOTOROLA ...
Page 8
... CLOCK SERIAL DATA INPUT A RESET LATCH CLOCK OUTPUT ENABLE SERIAL DATA OUTPUT SQ H NOTE: implies that the output high–impedance state. MOTOROLA TIMING DIAGRAM 8 High–Speed CMOS Logic Data DL129 — Rev 6 ...
Page 9
... PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS INCHES DIM MIN MAX MIN MAX F A 0.386 0.393 9.80 10.00 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 1.27 BSC 0.050 BSC G J 0.19 0.25 0.008 0.009 K 0.10 0.25 0.004 0.009 0.229 0.244 5.80 6.20 R 0.25 0.50 0.010 0.019 MOTOROLA ...
Page 10
... D 0.05 0.15 0.002 0.006 F 0.50 0.75 0.020 0.030 G 0.65 BSC 0.026 BSC H 0.18 0.28 0.007 0.011 J 0.09 0.20 0.004 0.008 J1 0.09 0.16 0.004 0.006 –W– K 0.19 0.30 0.007 0.012 K1 0.19 0.25 0.007 0.010 L 6.40 BSC 0.252 BSC Mfax is a trademark of Motorola, Inc. MC74HC595A/D High–Speed CMOS Logic Data DL129 — Rev 6 ...