PIC16F724-I/ML Microchip Technology, PIC16F724-I/ML Datasheet - Page 179

• Manufacturer Part Number: PIC16F724-I/ML
• Description: IC PIC MCU FLASH 4KX14 44-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F724-I/ML

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 14x8b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Controller Family/series: PIC16F
• No. Of I/o's: 36
• Ram Memory Size: 192Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• No. Of Pwm: RoHS Compliant
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 192 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 14 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

17.2.4
Once the SSP module has been enabled, it waits for a
Start condition to occur. Following the Start condition,
the 8 bits are shifted into the SSPSR register. All
incoming bits are sampled with the rising edge of the
clock line (SCL).
17.2.4.1
In 7-bit Addressing mode (Figure 17-10), the value of
register SSPSR<7:1> is compared to the value of reg-
ister SSPADD<7:1>. The address is compared on the
falling edge of the eighth clock (SCL) pulse. If the
addresses match, and the BF and SSPOV bits are
clear, the following events occur:
• The SSPSR register value is loaded into the
• The BF bit is set.
• An ACK pulse is generated.
• SSP interrupt flag bit, SSPIF of the PIR1 register,
17.2.4.2
In 10-bit Address mode, two address bytes need to be
received by the slave (Figure 17-11). The five Most Sig-
nificant bits (MSbs) of the first address byte specify if it
is a 10-bit address. The R/W bit of the SSPSTAT regis-
ter must specify a write so the slave device will receive
the second address byte. For a 10-bit address, the first
byte would equal ‘1111 0 A9 A8 0’, where A9 and
A8 are the two MSbs of the address.
© 2009 Microchip Technology Inc.
SSPBUF register.
is set (interrupt is generated if enabled) on the
falling edge of the ninth SCL pulse.
ADDRESSING
7-bit Addressing
10-bit Addressing
PIC16F72X/PIC16LF72X
The sequence of events for 10-bit address is as follows
for reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
If data is requested by the master, once the slave has
been addressed:
1.
2.
3.
4.
5.
17.2.4.3
The Address Masking register (SSPMSK) is only
accessible while the SSPM bits of the SSPCON
register are set to ‘1001’. In this register, the user can
select which bits of a received address the hardware
will compare when determining an address match. Any
bit that is set to a zero in the SSPMSK register, the
corresponding bit in the received address byte and
SSPADD register are ignored when determining an
address match. By default, the register is set to all
ones, requiring a complete match of a 7-bit address or
the lower eight bits of a 10-bit address.
Load SSPADD register with high byte of address.
Receive first (high) byte of address (bits SSPIF,
BF and UA of the SSPSTAT register are set).
Read the SSPBUF register (clears bit BF).
Clear the SSPIF flag bit.
Update the SSPADD register with second (low)
byte of address (clears UA bit and releases the
SCL line).
Receive low byte of address (bits SSPIF, BF and
UA are set).
Update the SSPADD register with the high byte
of address. If match releases SCL line, this will
clear bit UA.
Read the SSPBUF register (clears bit BF).
Clear flag bit SSPIF.
Receive repeated Start condition.
Receive repeat of high byte address with
R/W = 1, indicating a read.
BF bit is set and the CKP bit is cleared, stopping
SCL and indicating a read request.
SSPBUF is written, setting BF, with the data to
send to the master device.
CKP is set in software, releasing the SCL line.
Address Masking
DS41341E-page 179