PIC18F46K20-I/PT Microchip Technology, PIC18F46K20-I/PT Datasheet - Page 256

• Manufacturer Part Number: PIC18F46K20-I/PT
• Description: IC PIC MCU FLASH 32KX16 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46K20-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 35
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: CCP, ECCP, EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 14 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPDM164124 - KIT STARTER FOR PIC18F4XK20AC164305 - MODULE SKT FOR PM3 44TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2XK20/4XK20
18.4.1.5
1.
2.
3.
FIGURE 18-10:
FIGURE 18-11:
DS41303D-page 254
TX/CK pin
(SCKP = 0)
TX/CK pin
(SCKP = 1)
TRMT bit
RX/DT
pin
Write to
TXREG Reg
TXIF bit
(Interrupt Flag)
TXEN bit
Note:
Initialize the SPBRGH, SPBRG register pair and
the BRGH and BRG16 bits to achieve the
desired baud rate (see Section 18.3 “EUSART
Baud Rate Generator (BRG)”).
Set the RX/DT and TX/CK TRIS controls to ‘1’.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC. Set the
TRIS bits corresponding to the RX/DT and
TX/CK I/O pins.
‘1’
Synchronous Master Transmission
Set-up:
Sync Master mode, SPBRG = 0, continuous transmission of two 8-bit words.
Write Word 1
TXREG reg
RX/DT pin
TX/CK pin
TRMT bit
TXEN bit
TXIF bit
Write to
SYNCHRONOUS TRANSMISSION
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
bit 0
Write Word 2
bit 1
Word 1
bit 0
bit 2
Preliminary
bit 1
bit 7
4.
5.
6.
7.
8.
9.
Disable Receive mode by clearing bits SREN
and CREN.
Enable Transmit mode by setting the TXEN bit.
If 9-bit transmission is desired, set the TX9 bit.
If interrupts are desired, set the TXIE, GIE and
PEIE interrupt enable bits.
If 9-bit transmission is selected, the ninth bit
should be loaded in the TX9D bit.
Start transmission by loading data to the TXREG
register.
bit 2
bit 0
Word 2
bit 1
bit 6
© 2008 Microchip Technology Inc.
bit 7
bit 7
‘1’