ATMEGA8A-MU Atmel, ATMEGA8A-MU Datasheet - Page 234

• Manufacturer Part Number: ATMEGA8A-MU
• Description: MCU AVR 8K FLASH 16MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8A-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 16MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

24.7.5
8159D–AVR–02/11
Programming the EEPROM
Table 24-12. Programming the Flash Waveforms
Note:
The EEPROM is organized in pages, see
EEPROM, the program data is latched into a page buffer. This allows one page of data to be
programmed simultaneously. The programming algorithm for the EEPROM Data memory is as
follows (refer to
Data loading):
K: Repeat 3 through 5 until the entire buffer is filled.
L: Program EEPROM page.
1. A: Load Command “0001 0001”.
2. G: Load Address High byte (0x00 - 0xFF).
3. B: Load Address Low byte (0x00 - 0xFF).
4. C: Load Data (0x00 - 0xFF).
5. E: Latch data (give PAGEL a positive pulse).
1. Set BS1 to “0”.
2. Give WR a negative pulse. This starts programming of the EEPROM page. RDY/BSY
3. Wait until to RDY/BSY goes high before programming the next page.
RESET +12V
goes low.
(See
RDY/BSY
1. “XX” is don’t care. The letters refer to the programming description above.
PAGEL
XTAL1
DATA
XA1
XA0
BS1
BS2
WR
OE
Figure 24-2
“Programming the Flash” on page 232
0x10
A
ADDR. LOW
for signal waveforms).
B
DATA LOW
C
DATA HIGH
D
E
XX
ADDR. LOW
Table 24-6 on page
B
(1)
DATA LOW
C
F
DATA HIGH
for details on Command, Address and
D
E
XX
229. When programming the
ADDR. HIGH
G
ATmega8A
H
XX
234