PIC16F639-I/SS Microchip Technology, PIC16F639-I/SS Datasheet - Page 52

• Manufacturer Part Number: PIC16F639-I/SS
• Description: IC MCU FLASH 2KX14 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F639-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 20-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, LVD, POR, WDT
• Number Of I /o: 11
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SS1-1 - SOCKET TRANSITION 20DIP 20SSOPXLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPAC162066 - HEADER INTRFC MPLAB ICD2 20PINAC164307 - MODULE SKT FOR PM3 28SSOP
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F630/676
8.1
The EEADR register can address up to a maximum of
128 bytes of data EEPROM. Only seven of the eight
bits in the register (EEADR<6:0>) are required. The
MSb (bit 7) is ignored.
The upper bit should always be ‘0’ to remain upward
compatible with devices that have more data EEPROM
memory.
8.2
EECON1 is the control register with four low order bits
physically implemented. The upper four bits are non-
implemented and read as '0's.
Control bits RD and WR initiate read and write,
respectively. These bits cannot be cleared, only set, in
software. They are cleared in hardware at completion
REGISTER 8-3:
DS40039C-page 50
EEADR
EECON1 AND EECON2
REGISTERS
bit 7-4
bit 3
bit 2
bit 1
bit 0
EECON1 — EEPROM CONTROL REGISTER (ADDRESS: 9Ch)
bit 7
Unimplemented: Read as ‘0’
WRERR: EEPROM Error Flag bit
1 = A write operation is prematurely terminated (any MCLR Reset, any WDT Reset during
0 = The write operation completed
WREN: EEPROM Write Enable bit
1 = Allows write cycles
0 = Inhibits write to the data EEPROM
WR: Write Control bit
1 = Initiates a write cycle (The bit is cleared by hardware once write is complete. The WR bit
0 = Write cycle to the data EEPROM is complete
RD: Read Control bit
1 = Initiates an EEPROM read (Read takes one cycle. RD is cleared in hardware. The RD bit
0 = Does not initiate an EEPROM read
Legend:
S = Bit can only be set
R = Readable bit
- n = Value at POR
U-0
normal operation or BOD detect)
can only be set, not cleared, in software.)
—
can only be set, not cleared, in software.)
U-0
—
U-0
—
W = Writable bit
’1’ = Bit is set
U-0
—
of the read or write operation. The inability to clear the
WR bit in software prevents the accidental, premature
termination of a write operation.
The WREN bit, when set, will allow a write operation.
On power-up, the WREN bit is clear. The WRERR bit
is set when a write operation is interrupted by a MCLR
Reset, or a WDT Time-out Reset during normal
operation. In these situations, following RESET, the
user can check the WRERR bit, clear it, and rewrite
the location. The data and address will be cleared,
therefore, the EEDATA and EEADR registers will
need to be re-initialized.
Interrupt flag bit EEIF in the PIR1 register is set when
write is complete. This bit must be cleared in software.
EECON2 is not a physical register. Reading EECON2
will read all '0's. The EECON2 register is used
exclusively in the Data EEPROM write sequence.
WRERR
R/W-x
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
WREN
R/W-0
 2003 Microchip Technology Inc.
x = Bit is unknown
R/S-0
WR
R/S-0
RD
bit 0