PIC24HJ12GP201-I/P Microchip Technology, PIC24HJ12GP201-I/P Datasheet - Page 168

• Manufacturer Part Number: PIC24HJ12GP201-I/P
• Description: IC PIC MCU FLASH 4KX24 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ12GP201-I/P

• Program Memory Type: FLASH
• Program Memory Size: 12KB (4K x 24)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 13
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 1 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit or 6-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164337 - MODULE SOCKET FOR PM3 40DIP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24HJ12GP201/202
18.2
All of the PIC24HJ12GP201/202 devices power their
core digital logic at a nominal 2.5V. This can create a
conflict for designs that are required to operate at a
higher typical voltage, such as 3.3V. To simplify system
design, all devices in the PIC24HJ12GP201/202 family
incorporate an on-chip regulator that allows the device
to run its core logic from V
The regulator provides power to the core from the other
V
(less than 5 ohms) capacitor (such as tantalum or
ceramic) must be connected to the V
(Figure 18-1). This helps to maintain the stability of the
regulator. The recommended value for the filter capac-
itor is provided in Table 21-13 located in Section 21.1
“DC Characteristics”.
On a POR
voltage regulator to generate an output voltage. During
this time, designated as T
disabled. T
resumes operation after any power-down.
FIGURE 18-1:
DS70282B-page 166
DD
Note 1:
pins. When the regulator is enabled, a low-ESR
On-Chip Voltage Regulator
,
STARTUP
it takes approximately 20 μs for the on-chip
C
F
These are typical operating voltages. Refer
to TABLE 21-13: “Internal Voltage Regu-
lator Specifications” located in
Section 21.1 “DC Characteristics” for the
full operating ranges of V
3.3V
is applied every time the device
CONNECTIONS FOR THE
ON-CHIP VOLTAGE
REGULATOR
V
V
V
DD
DDCORE
SS
DD
PIC24H
STARTUP
.
/V
CAP
, code execution is
DD
DDCORE
and V
(1)
DDCORE
/V
CAP
.
Preliminary
pin
18.3
The Brown-out Reset (BOR) module is based on an
internal voltage reference circuit that monitors the reg-
ulated voltage V
module is to generate a device Reset when a brown-
out condition occurs. Brown-out conditions are gener-
ally caused by glitches on the AC mains (for example,
missing portions of the AC cycle waveform due to bad
power transmission lines, or voltage sags due to exces-
sive current draw when a large inductive load is turned
on).
A BOR generates a Reset pulse, which resets the
device. The BOR selects the clock source, based on
the device Configuration bit values (FNOSC<2:0> and
POSCMD<1:0>).
If an oscillator mode is selected, the BOR activates the
Oscillator Start-up Timer (OST). The system clock is
held until OST expires. If the PLL is used, the clock is
held until the LOCK bit (OSCCON<5>) is ‘1’.
Concurrently, the PWRT time-out (TPWRT) will be
applied before the internal Reset is released. If TPWRT
= 0 and a crystal oscillator is being used, a nominal
delay of TFSCM = 100 is applied. The total delay in this
case is TFSCM.
The BOR Status bit (RCON<1>) is set to indicate that a
BOR has occurred. The BOR circuit, if enabled, contin-
ues to operate while in Sleep or Idle modes and resets
the device should VDD fall below the BOR threshold
voltage.
BOR: Brown-Out Reset
DDCORE
. The main purpose of the BOR
© 2007 Microchip Technology Inc.