PIC18F45J50-I/PT Microchip Technology, PIC18F45J50-I/PT Datasheet - Page 307
![IC PIC MCU FLASH 32K 2V 44-TQFP](/photos/6/82/68251/c04-076_pt_sml.jpg)
PIC18F45J50-I/PT
Manufacturer Part Number
PIC18F45J50-I/PT
Description
IC PIC MCU FLASH 32K 2V 44-TQFP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.PIC18LF24J50-ISS.pdf
(554 pages)
2.PIC18LF24J50-ISS.pdf
(12 pages)
3.PIC18F26J11-ISO.pdf
(28 pages)
Specifications of PIC18F45J50-I/PT
Program Memory Type
FLASH
Program Memory Size
32KB (16K x 16)
Package / Case
44-TQFP, 44-VQFP
Core Processor
PIC
Core Size
8-Bit
Speed
48MHz
Connectivity
I²C, SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
34
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
2.15 V ~ 3.6 V
Data Converters
A/D 13x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
4 KB
Interface Type
EUSART, I2C, SPI
Maximum Clock Frequency
48 MHz
Number Of Timers
5
Operating Supply Voltage
2.25 V to 2.75 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, MA180024, DM183022
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 13 Channel
Controller Family/series
PIC18
No. Of I/o's
22
Ram Memory Size
3776Byte
Cpu Speed
48MHz
No. Of Timers
5
Embedded Interface Type
EUSART, I2C, SPI
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F45J50-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 307 of 554
- Download datasheet (9Mb)
18.5.10
Transmission of a data byte, a 7-bit address or the
other half of a 10-bit address, is accomplished by
simply writing a value to the SSPxBUF register. This
action will set the Buffer Full flag bit, BF, and allow the
BRG to begin counting and start the next transmission.
Each bit of address/data will be shifted out onto the
SDAx pin after the falling edge of SCLx is asserted (see
data hold time specification parameter 106). SCLx is
held low for one BRG rollover count (T
should be valid before SCLx is released high (see data
setup time specification parameter 107). When the
SCLx pin is released high, it is held that way for T
The data on the SDAx pin must remain stable for that
duration and some hold time after the next falling edge
of SCLx. After the eighth bit is shifted out (the falling
edge of the eighth clock), the BF flag is cleared and the
master releases SDAx. This allows the slave device
being addressed to respond with an ACK bit during the
ninth bit time if an address match occurred, or if data
was received properly. The status of ACK is written into
the ACKDT bit on the falling edge of the ninth clock.
If the master receives an Acknowledge, the Acknowl-
edge Status bit, ACKSTAT, is cleared; if not, the bit is
set. After the ninth clock, the SSPxIF bit is set and the
master clock (BRG) is suspended until the next data
byte is loaded into the SSPxBUF, leaving SCLx low and
SDAx unchanged (Figure 18-23).
After the write to the SSPxBUF, each bit of the address
will be shifted out on the falling edge of SCLx until all
seven address bits and the R/W bit are completed. On
the falling edge of the eighth clock, the master will
deassert the SDAx pin, allowing the slave to respond
with an Acknowledge. On the falling edge of the ninth
clock, the master will sample the SDAx pin to see if the
address was recognized by a slave. The status of the
ACK bit is loaded into the ACKSTAT status bit
(SSPxCON2<6>). Following the falling edge of the
ninth clock transmission of the address, the SSPxIF
flag is set, the BF flag is cleared and the BRG is turned
off until another write to the SSPxBUF takes place,
holding SCLx low and allowing SDAx to float.
18.5.10.1
In Transmit mode, the BF bit (SSPxSTAT<0>) is set
when the CPU writes to SSPxBUF and is cleared when
all eight bits are shifted out.
18.5.10.2
If the user writes the SSPxBUF when a transmit is
already in progress (i.e., SSPxSR is still shifting out a
data byte), the WCOL bit is set and the contents of the
buffer are unchanged (the write does not occur) after
2 T
within 2 T
updated. This may result in a corrupted transfer.
© 2009 Microchip Technology Inc.
CY
after the SSPxBUF write. If SSPxBUF is rewritten
CY
I
TRANSMISSION
2
, the WCOL bit is set and SSPxBUF is
C MASTER MODE
BF Status Flag
WCOL Status Flag
BRG
). Data
BRG
.
PIC18F46J50 FAMILY
The user should verify that the WCOL bit is clear after
each write to SSPxBUF to ensure the transfer is correct.
In all cases, WCOL must be cleared in software.
18.5.10.3
In Transmit mode, the ACKSTAT bit (SSPxCON2<6>)
is cleared when the slave has sent an Acknowledge
(ACK = 0) and is set when the slave does not Acknowl-
edge (ACK = 1). A slave sends an Acknowledge when
it has recognized its address (including a general call),
or when the slave has properly received its data.
18.5.11
Master mode reception is enabled by programming the
Receive Enable bit, RCEN (SSPxCON2<3>).
The BRG begins counting and on each rollover, the
state of the SCLx pin changes (high-to-low/low-to-high)
and data is shifted into the SSPxSR. After the falling
edge of the eighth clock, the receive enable flag is
automatically cleared, the contents of the SSPxSR are
loaded into the SSPxBUF, the BF flag bit is set, the
SSPxIF flag bit is set and the BRG is suspended from
counting, holding SCLx low. The MSSP is now in Idle
state awaiting the next command. When the buffer is
read by the CPU, the BF flag bit is automatically
cleared. The user can then send an Acknowledge bit at
the end of reception by setting the Acknowledge
Sequence Enable bit, ACKEN (SSPxCON2<4>).
18.5.11.1
In receive operation, the BF bit is set when an address
or data byte is loaded into SSPxBUF from SSPxSR. It
is cleared when the SSPxBUF register is read.
18.5.11.2
In receive operation, the SSPOV bit is set when 8 bits
are received into the SSPxSR and the BF flag bit is
already set from a previous reception.
18.5.11.3
If users write the SSPxBUF when a receive is already
in progress (i.e., SSPxSR is still shifting in a data byte),
the WCOL bit is set and the contents of the buffer are
unchanged (the write does not occur).
Note:
I
The MSSP module must be in an inactive
state before the RCEN bit is set or the
RCEN bit will be disregarded.
2
ACKSTAT Status Flag
C MASTER MODE RECEPTION
BF Status Flag
SSPOV Status Flag
WCOL Status Flag
DS39931C-page 307
Related parts for PIC18F45J50-I/PT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-4.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.85VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: