PIC18F4221-I/P Microchip Technology, PIC18F4221-I/P Datasheet - Page 47

• Manufacturer Part Number: PIC18F4221-I/P
• Description: IC PIC MCU FLASH 2KX16 400IP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4221-I/P

• Program Memory Type: FLASH
• Program Memory Size: 4KB (2K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.0
The
differentiate between various kinds of Reset:
a)
b)
c)
d)
e)
f)
g)
h)
This section discusses Resets generated by MCLR,
POR and BOR and covers the operation of the various
start-up timers. Stack Reset events are covered in
Section 6.1.2.4 “Stack Full and Underflow Resets”.
WDT Resets are covered in Section 24.2 “Watchdog
Timer (WDT)”.
FIGURE 5-1:
© 2009 Microchip Technology Inc.
Note 1: This is the INTRC source from the internal oscillator block and is separate from the RC oscillator of the CLKI pin.
OSC1
MCLR
V
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during power-managed modes
Watchdog Timer (WDT) Reset (during
execution)
Programmable Brown-out Reset (BOR)
RESET Instruction
Stack Full Reset
Stack Underflow Reset
DD
PIC18F2221/2321/4221/4321
2: See Table 5-2 for time-out situations.
RESET
Instruction
INTRC
RESET
OST/PWRT
Pointer
32 μs
Stack
( )_IDLE
Brown-out
Time-out
V
(1)
Detect
Sleep
DD
WDT
Reset
Rise
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
OST
PIC18F2221/2321/4221/4321 FAMILY
PWRT
Stack Full/Underflow Reset
External Reset
MCLRE
10-bit Ripple Counter
11-Bit Ripple Counter
POR Pulse
BOREN
1024 Cycles
65.5 ms
family
devices
A simplified block diagram of the On-Chip Reset Circuit
is shown in Figure 5-1.
5.1
Device Reset events are tracked through the RCON
register (Register 5-1). The lower five bits of the regis-
ter indicate that a specific Reset event has occurred. In
most cases, these bits can only be cleared by the event
and must be set by the application after the event. The
state of these flag bits, taken together, can be read to
indicate the type of Reset that just occurred. This is
described in more detail in Section 5.6 “Reset State
of Registers”.
The RCON register also has control bits for setting
interrupt priority (IPEN) and software control of the
BOR (SBOREN). Interrupt priority is discussed in
Section 10.0 “Interrupts”. BOR is covered in
Section 5.4 “Brown-out Reset (BOR)”.
RCON Register
S
R
DS39689F-page 47
Q
Enable OST
Enable PWRT
Chip_Reset
(2)