PIC16F84A-20I/SS Microchip Technology, PIC16F84A-20I/SS Datasheet - Page 400

• Manufacturer Part Number: PIC16F84A-20I/SS
• Description: IC MCU FLASH 1KX14 EE 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F84A-20I/SS

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 13
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 68 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SSOP
• Controller Family/series: PIC16F
• No. Of I/o's: 13
• Eeprom Memory Size: 64Byte
• Ram Memory Size: 68Byte
• Cpu Speed: 20MHz
• No. Of Timers: 1
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 68 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• Data Rom Size: 64 B
• Height: 1.75 mm
• Length: 7.2 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4 V
• Width: 5.3 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SS1-1 - SOCKET TRANSITION 20DIP 20SSOPI3-DB16F84A - BOARD DAUGHTER ICEPIC3AC164307 - MODULE SKT FOR PM3 28SSOPAC164018 - MODULE SKT PROMATEII 20SSOP
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PICmicro MID-RANGE MCU FAMILY
21.15
DS31021A-page 21-16
Design Tips
Question 1:
Answer 1:
1.
2.
3.
Question 2:
Answer 2:
After the holding capacitor is disconnected from the input channel, one T
set, the input channel may be changed.
Question 3:
Answer 3:
A very good reference for understanding A/D conversions is the “Analog-Digital Conversion
Handbook” third edition, published by Prentice Hall (ISBN 0-13-03-2848-0).
Make sure you are meeting all of the timing specifications. If you are turning the A/D mod-
ule off and on, there is a minimum delay you must wait before taking a sample, if you are
changing input channels, there is a minimum delay you must wait for this as well, and
finally there is Tad, which is the time selected for each bit conversion. This is selected in
ADCON0 and should be between 2 and 6 s. If T
converted before the conversion is terminated, and if T
the sampling capacitor can droop before the conversion is complete. These timing speci-
fications are provided in the data book in a table or by way of a formula, and should be
looked up for your specific part and circumstances.
Often the source impedance of the analog signal is high (greater than 1k ohms) so the
current drawn from the source to charge the sample capacitor can affect accuracy. If the
input signal does not change too quickly, try putting a 0.1 F capacitor on the analog input.
This capacitor will charge to the analog voltage being sampled, and supply the instanta-
neous current needed to charge the 51.2 pf internal holding capacitor.
Finally, straight from the data book: “In systems where the device frequency is low, use of
the A/D clock derived from the device oscillator is preferred...this reduces, to a large
extent, the effects of digital switching noise.” and “In systems where the device will enter
SLEEP mode after start of A/D conversion, the RC clock source selection is required. This
method gives the highest accuracy.”
I am using one of your PIC16C7X devices, and I find that the Analog to Dig-
ital Converter result is not always accurate. What can I do to improve accu-
racy?
After starting an A/D conversion may I change the input channel (for my
next conversion)?
Do you know of a good reference on A/D’s?
AD
is too short, the result may not be fully
AD
is made too long the voltage on
1997 Microchip Technology Inc.
AD
after the GO bit is