PIC18F4520-I/P Microchip Technology, PIC18F4520-I/P Datasheet - Page 139
![IC MCU FLASH 16KX16 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC18F4520-I/P
Manufacturer Part Number
PIC18F4520-I/P
Description
IC MCU FLASH 16KX16 40DIP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC18F2221-ISO.pdf
(46 pages)
3.PIC18F2420-IML.pdf
(412 pages)
4.PIC18F2420-IML.pdf
(16 pages)
5.PIC18F2420-IML.pdf
(8 pages)
6.PIC18F2420-IML.pdf
(6 pages)
7.PIC18F2420-IML.pdf
(8 pages)
8.PIC18F2420-IML.pdf
(4 pages)
9.PIC18F4420-IP.pdf
(390 pages)
Specifications of PIC18F4520-I/P
Program Memory Type
FLASH
Program Memory Size
32KB (16K x 16)
Package / Case
40-DIP (0.600", 15.24mm)
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
36
Eeprom Size
256 x 8
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 13x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
1536 B
Interface Type
MSSP, SPI, I2C, PSP, USART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
36
Number Of Timers
1 x 8
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, 53275-917, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163022
Minimum Operating Temperature
- 40 C
On-chip Adc
13 bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F4520-I/P
Manufacturer:
ST
Quantity:
104
Part Number:
PIC18F4520-I/P
Manufacturer:
MICROCH
Quantity:
20 000
Company:
Part Number:
PIC18F4520-I/PT
Manufacturer:
TI
Quantity:
14 300
Company:
Part Number:
PIC18F4520-I/PT
Manufacturer:
Microchip Technology
Quantity:
33 055
Company:
Part Number:
PIC18F4520-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC18F4520-I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
14.2
Timer3 can be configured for 16-bit reads and writes
(see Figure 14-2). When the RD16 control bit
(T3CON<7>) is set, the address for TMR3H is mapped
to a buffer register for the high byte of Timer3. A read
from TMR3L will load the contents of the high byte of
Timer3 into the Timer3 High Byte Buffer register. This
provides the user with the ability to accurately read all
16 bits of Timer1 without having to determine whether
a read of the high byte, followed by a read of the low
byte, has become invalid due to a rollover between
reads.
A write to the high byte of Timer3 must also take place
through the TMR3H Buffer register. The Timer3 high
byte is updated with the contents of TMR3H when a
write occurs to TMR3L. This allows a user to write all
16 bits to both the high and low bytes of Timer3 at once.
The high byte of Timer3 is not directly readable or
writable in this mode. All reads and writes must take
place through the Timer3 High Byte Buffer register.
Writes to TMR3H do not clear the Timer3 prescaler.
The prescaler is only cleared on writes to TMR3L.
14.3
The Timer1 internal oscillator may be used as the clock
source for Timer3. The Timer1 oscillator is enabled by
setting the T1OSCEN (T1CON<3>) bit. To use it as the
Timer3 clock source, the TMR3CS bit must also be set.
As previously noted, this also configures Timer3 to
increment on every rising edge of the oscillator source.
The Timer1 oscillator is described in Section 12.0
“Timer1 Module”.
TABLE 14-1:
2004 Microchip Technology Inc.
INTCON
PIR2
PIE2
IPR2
TMR3L
TMR3H
T1CON
T3CON
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the Timer3 module.
Name
Timer3 16-Bit Read/Write Mode
Using the Timer1 Oscillator as the
Timer3 Clock Source
Timer3 Register, Low Byte
Timer3 Register, High Byte
GIE/GIEH PEIE/GIEL TMR0IE
OSCFIE
OSCFIP
OSCFIF
RD16
RD16
Bit 7
REGISTERS ASSOCIATED WITH TIMER3 AS A TIMER/COUNTER
T3CCP2
T1RUN
CMIF
CMIE
CMIP
Bit 6
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC
T3CKPS1 T3CKPS0 T3CCP1
Bit 5
—
—
—
PIC18F2420/2520/4420/4520
INT0IE
Preliminary
EEIE
EEIP
Bit 4
EEIF
BCLIE
BCLIP
BCLIF
RBIE
14.4
The TMR3 register pair (TMR3H:TMR3L) increments
from 0000h to FFFFh and overflows to 0000h. The
Timer3 interrupt, if enabled, is generated on overflow
and is latched in interrupt flag bit, TMR3IF (PIR2<1>).
This interrupt can be enabled or disabled by setting or
clearing the Timer3 Interrupt Enable bit, TMR3IE
(PIE2<1>).
14.5
If either of the CCP modules is configured to use
Timer3 and to generate a Special Event Trigger
in Compare
CCP2M3:CCP2M0 = 1011), this signal will reset
Timer3. It will also start an A/D conversion if the A/D
module is enabled (see Section 15.3.4 “Special
Event Trigger” for more information).
The module must be configured as either a timer or
synchronous counter to take advantage of this feature.
When used this way, the CCPR2H:CCPR2L register
pair effectively becomes a period register for Timer3.
If Timer3 is running in Asynchronous Counter mode,
the Reset operation may not work.
In the event that a write to Timer3 coincides with a
Special Event Trigger from a CCP module, the write will
take precedence.
Bit 3
Note:
Timer3 Interrupt
Resetting Timer3 Using the CCP
Special Event Trigger
T3SYNC
TMR0IF
HLVDIE
HLVDIP
HLVDIF
Bit 2
The Special Event Triggers from the
CCP2 module will not set the TMR3IF
interrupt flag bit (PIR1<0>).
mode
TMR1CS TMR1ON
TMR3CS TMR3ON
TMR3IF
TMR3IE
TMR3IP
INT0IF
Bit 1
(CCP1M3:CCP1M0
CCP2IE
CCP2IP
CCP2IF
RBIF
Bit 0
DS39631A-page 137
on page
Values
Reset
49
52
52
52
51
51
50
51
or