PIC24HJ64GP510-I/PT Microchip Technology, PIC24HJ64GP510-I/PT Datasheet - Page 184
![IC PIC MCU FLASH 32KX16 100TQFP](/photos/12/13/121330/c04-100-tqfp_sml.jpg)
PIC24HJ64GP510-I/PT
Manufacturer Part Number
PIC24HJ64GP510-I/PT
Description
IC PIC MCU FLASH 32KX16 100TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Hr
Datasheets
1.PIC24HJ12GP201-ISO.pdf
(84 pages)
2.PIC24HJ64GP206-IPT.pdf
(292 pages)
3.PIC24HJ64GP206-IPT.pdf
(8 pages)
4.PIC24HJ64GP206-IPT.pdf
(20 pages)
5.PIC24HJ64GP206-IPT.pdf
(26 pages)
6.PIC24HJ128GP306-IPT.pdf
(288 pages)
Specifications of PIC24HJ64GP510-I/PT
Core Size
16-Bit
Program Memory Size
64KB (22K x 24)
Core Processor
PIC
Speed
40 MIPs
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
85
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 32x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TFQFP
Controller Family/series
PIC24
No. Of I/o's
85
Ram Memory Size
8KB
Cpu Speed
40MIPS
No. Of Timers
13
No. Of Pwm Channels
8
Processor Series
PIC24HJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
8 KB
Interface Type
CAN, I2C, SPI, UART
Maximum Clock Frequency
40 MHz
Number Of Programmable I/os
85
Number Of Timers
13
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005
Minimum Operating Temperature
- 40 C
On-chip Adc
12 bit, 32 Channel
A/d Bit Size
12 bit
A/d Channels Available
32
Height
1 mm
Length
12 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3 V
Width
12 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARDAC164333 - MODULE SKT FOR PM3 100QFPDM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24HJ64GP510-I/PT
Manufacturer:
Microchip
Quantity:
104
Company:
Part Number:
PIC24HJ64GP510-I/PT
Manufacturer:
MICROCHIP
Quantity:
455
Company:
Part Number:
PIC24HJ64GP510-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC24H
18.5.7
Transmit interrupts can be divided into 2 major groups,
each including various conditions that generate
interrupts:
• Transmit Interrupt:
• Transmit Error Interrupts:
FIGURE 18-2:
DS70175C-page 182
T
- Transmitter Warning Interrupt:
- Transmitter Error Passive:
- Bus Off:
Note:
At least one of the three transmit buffers is empty
(not scheduled) and can be loaded to schedule a
message for transmission. Reading the TXnIF
flags will indicate which transmit buffer is available
and caused the interrupt.
A transmission error interrupt will be indicated by
the ERRIF flag. This flag shows that an error con-
dition occurred. The source of the error can be
determined by checking the error flags in the CAN
Interrupt Flag register, CiINTF. The flags in this
register are related to receive and transmit errors.
Input Signal
Q
The TXWAR bit indicates that the transmit error
counter has reached the CPU warning limit
of 96.
The TXEP bit (CiINTF<12>) indicates that the
transmit error counter has exceeded the error
passive limit of 127 and the module has gone to
error passive state.
The TXBO bit (CiINTF<13>) indicates that the
transmit error counter has exceeded 255 and
the module has gone to the bus off state.
TRANSMIT INTERRUPTS
Both ECAN1 and ECAN2 can trigger a
DMA data transfer. If C1TX, C1RX, C2TX
or C2RX is selected as a DMA IRQ
source, a DMA transfer occurs when the
C1TXIF, C1RXIF, C2TXIF or C2RXIF bit
gets set as a result of an ECAN1 or
ECAN2 transmission or reception.
Sync
ECAN™ MODULE BIT TIMING
Segment
Prop
Segment 1
Phase
Preliminary
Sample Point
18.6
All nodes on any particular CAN bus must have the
same nominal bit rate. In order to set the baud rate, the
following parameters have to be initialized:
• Synchronization Jump Width
• Baud Rate Prescaler
• Phase Segments
• Length Determination of Phase Segment 2
• Sample Point
• Propagation Segment bits
18.6.1
All controllers on the CAN bus must have the same
baud rate and bit length. However, different controllers
are not required to have the same master oscillator
clock. At different clock frequencies of the individual
controllers, the baud rate has to be adjusted by
adjusting the number of time quanta in each segment.
The nominal bit time can be thought of as being divided
into separate non-overlapping time segments. These
segments are shown in Figure 18-2.
• Synchronization Segment (Sync Seg)
• Propagation Time Segment (Prop Seg)
• Phase Segment 1 (Phase1 Seg)
• Phase Segment 2 (Phase2 Seg)
The time segments and also the nominal bit time are
made up of integer units of time called time quanta or
T
of 8 T
the minimum nominal bit time is 1 sec corresponding
to a maximum bit rate of 1 MHz.
Q
. By definition, the nominal bit time has a minimum
Q
and a maximum of 25 T
Baud Rate Setting
BIT TIMING
Segment 2
Phase
© 2006 Microchip Technology Inc.
Q
. Also, by definition,
Sync