C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 151

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

Bit7:
Bits6–5: Unused. Read = 00b. Write = don’t care.
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
ISOUD
R/W
Bit7
ISOUD: ISO Update
This bit affects all IN Isochronous endpoints.
0: When software writes INPRDY = ‘1’, USB0 will send the packet when the next IN token is
received.
1: When software writes INPRDY = ‘1’, USB0 will wait for a SOF token before sending the
packet. If an IN token is received before a SOF token, USB0 will send a zero-length data
packet.
USBINH: USB0 Inhibit
This bit is set to ‘1’ following a power-on reset (POR) or an asynchronous USB0 reset (see
Bit3: RESET). Software should clear this bit after all USB0 and transceiver initialization is
complete. Software cannot set this bit to ‘1’.
0: USB0 enabled.
1: USB0 inhibited. All USB traffic is ignored.
USBRST: Reset Detect
Writing ‘1’ to this bit forces an asynchronous USB0 reset. Reading this bit provides bus reset
status information.
Read:
0: Reset signaling is not present on the bus.
1: Reset signaling detected on the bus.
RESUME: Force Resume
Software can force resume signaling on the bus to wake USB0 from suspend mode. Writing
a ‘1’ to this bit while in Suspend mode (SUSMD = ‘1’) forces USB0 to generate Resume sig-
naling on the bus (a remote Wakeup event). Software should write RESUME = ‘0’ after
10 ms to15 ms to end the Resume signaling. An interrupt is generated, and hardware clears
SUSMD, when software writes RESUME = ‘0’.
SUSMD: Suspend Mode
Set to ‘1’ by hardware when USB0 enters suspend mode. Cleared by hardware when soft-
ware writes RESUME = ‘0’ (following a remote wakeup) or reads the CMINT register after
detection of Resume signaling on the bus.
0: USB0 not in suspend mode.
1: USB0 in suspend mode.
SUSEN: Suspend Detection Enable
0: Suspend detection disabled. USB0 will ignore suspend signaling on the bus.
1: Suspend detection enabled. USB0 will enter suspend mode if it detects suspend signaling
on the bus.
R/W
Bit6
-
USB Register Definition 15.8. POWER: USB0 Power
R/W
Bit5
-
USBINH
R/W
Bit4
USBRST RESUME
Rev. 1.4
R/W
Bit3
R/W
Bit2
SUSMD
Bit1
R
C8051F320/1
SUSEN
R/W
Bit0
USB Address:
00010000
Reset Value
0x01
151