PIC12F675-E/SN Microchip Technology, PIC12F675-E/SN Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12F675-E/SN
Manufacturer Part Number
PIC12F675-E/SN
Description
IC MCU CMOS 1K FLASH W/AD 8-SOIC
Manufacturer
Microchip Technology
Series
PIC® 12Fr
Datasheets
1.PIC12F629T-ISN.pdf
(136 pages)
2.PIC12F629T-ISN.pdf
(8 pages)
3.PIC12F629T-ISN.pdf
(24 pages)
4.PIC12F675-ESN.pdf
(132 pages)
Specifications of PIC12F675-E/SN
Program Memory Type
FLASH
Program Memory Size
1.75KB (1K x 14)
Package / Case
8-SOIC (3.9mm Width)
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
POR, WDT
Number Of I /o
5
Eeprom Size
128 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Processor Series
PIC12F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
64 B
Interface Type
RS- 232/USB
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
6
Number Of Timers
2
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 53270-913
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
Minimum Operating Temperature
- 40 C
On-chip Adc
4-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
3.0
There are as many as six general purpose I/O pins
available. Depending on which peripherals are
enabled, some or all of the pins may not be available as
general purpose I/O. In general, when a peripheral is
enabled, the associated pin may not be used as a
general purpose I/O pin.
3.1
GPIO is an 6-bit wide, bi-directional port. The corre-
sponding data direction register is TRISIO. Setting a
TRISIO bit (= 1) will make the corresponding GPIO pin
an input (i.e., put the corresponding output driver in a
Hi-impedance mode). Clearing a TRISIO bit (= 0) will
make the corresponding GPIO pin an output (i.e., put
the contents of the output latch on the selected pin).
The exception is GP3, which is input only and its
TRISIO bit will always read as ‘1’. Example 3-1 shows
how to initialize GPIO.
Reading the GPIO register reads the status of the pins,
whereas writing to it will write to the port latch. All write
operations are read-modify-write operations. There-
fore, a write to a port implies that the port pins are read,
this value is modified, and then written to the port data
latch. GP3 reads ‘0’ when MCLREN = 1.
The TRISIO register controls the direction of the
GP pins, even when they are being used as analog
inputs. The user must ensure the bits in the TRISIO
REGISTER 3-1:
2003 Microchip Technology Inc.
Note:
GPIO PORT
GPIO and the TRISIO Registers
bit 7-6:
bit 5-0:
Additional information on I/O ports may be
found in the PICmicro™ Mid-Range Refer-
ence Manual, (DS33023)
GPIO — GPIO REGISTER (ADDRESS: 05h)
Unimplemented: Read as ’0’
GPIO<5:0>: General Purpose I/O pin.
1 = Port pin is >V
0 = Port pin is <V
bit 7
Legend:
R = Readable bit
- n = Value at POR
U-0
—
U-0
—
IH
IL
GPIO5
R/W-x
W = Writable bit
’1’ = Bit is set
GPIO4
R/W-x
register are maintained set when using them as analog
inputs. I/O pins configured as analog inputs always
read ‘0’.
EXAMPLE 3-1:
3.2
Every GPIO pin on the PIC12F629/675 has an
interrupt-on-change option and every GPIO pin, except
GP3, has a weak pull-up option. The next two sections
describe these functions.
3.2.1
Each of the GPIO pins, except GP3, has an individually
configurable weak internal pull-up. Control bits WPUx
enable or disable each pull-up. Refer to Register 3-3.
Each weak pull-up is automatically turned off when the
port pin is configured as an output. The pull-ups are
disabled on a Power-on Reset by the GPPU bit
(OPTION<7>).
bcf
clrf
movlw
movwf
bsf
clrf
movlw
movwf
Note:
Additional Pin Functions
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
STATUS,RP0
GPIO
07h
CMCON
STATUS,RP0
ANSEL
0Ch
TRISIO
GPIO3
R/W-x
The ANSEL (9Fh) and CMCON (19h)
registers (9Fh) must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’. The ANSEL register is defined for
the PIC12F675.
WEAK PULL-UP
PIC12F629/675
INITIALIZING GPIO
GPIO2
R/W-x
;Bank 0
;Init GPIO
;Set GP<2:0> to
;digital IO
;Bank 1
;Digital I/O
;Set GP<3:2> as inputs
;and set GP<5:4,1:0>
;as outputs
x = Bit is unknown
GPIO1
R/W-x
DS41190C-page 19
GPIO0
R/W-x
bit 0