PIC12F675-E/SN Microchip Technology, PIC12F675-E/SN Datasheet - Page 69
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12F675-E/SN
Manufacturer Part Number
PIC12F675-E/SN
Description
IC MCU CMOS 1K FLASH W/AD 8-SOIC
Manufacturer
Microchip Technology
Series
PIC® 12Fr
Datasheets
1.PIC12F629T-ISN.pdf
(136 pages)
2.PIC12F629T-ISN.pdf
(8 pages)
3.PIC12F629T-ISN.pdf
(24 pages)
4.PIC12F675-ESN.pdf
(132 pages)
Specifications of PIC12F675-E/SN
Program Memory Type
FLASH
Program Memory Size
1.75KB (1K x 14)
Package / Case
8-SOIC (3.9mm Width)
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
POR, WDT
Number Of I /o
5
Eeprom Size
128 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Processor Series
PIC12F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
64 B
Interface Type
RS- 232/USB
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
6
Number Of Timers
2
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 53270-913
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
Minimum Operating Temperature
- 40 C
On-chip Adc
4-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
9.8
If
programmed, the on-chip program memory can be
read out for verification purposes.
9.9
Four memory locations (2000h-2003h) are designated
as ID locations where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution but are
readable and writable during Program/Verify. Only the
Least Significant 7 bits of the ID locations are used.
9.10
The PIC12F629/675 microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for:
• power
• ground
• programming voltage
This allows customers to manufacture boards with
unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom
firmware to be programmed.
The device is placed into a Program/Verify mode by
holding the GP0 and GP1 pins low, while raising the
MCLR (V
Specification). GP0 becomes the programming data
and GP1 becomes the programming clock. Both GP0
and GP1 are Schmitt Trigger inputs in this mode.
After RESET, to place the device into Programming/
Verify mode, the program counter (PC) is at location
00h. A 6-bit command is then supplied to the device.
Depending on the command, 14-bits of program data
are then supplied to or from the device, depending on
whether the command was a load or a read. For
complete details of serial programming, please refer to
the Programming Specifications.
A typical In-Circuit Serial Programming connection is
shown in Figure 9-14.
2003 Microchip Technology Inc.
Note:
the
Code Protection
ID Locations
In-Circuit Serial Programming
code
PP
The entire data EEPROM and FLASH
program memory will be erased when the
code protection is turned off. The INTOSC
calibration data is also erased. See
PIC12F629/675 Programming Specifica-
tion for more information.
) pin from V
protection
IL
to V
bit(s)
IHH
(see Programming
have
not
been
FIGURE 9-14:
9.11
Since in-circuit debugging requires the loss of clock,
data and MCLR pins, MPLAB
an 8-pin device is not practical. A special 14-pin
PIC12F675-ICD device is used with MPLAB ICD 2 to
provide separate clock, data and MCLR pins and frees
all normally available pins to the user.
This special ICD device is mounted on the top of the
header and its signals are routed to the MPLAB ICD 2
connector. On the bottom of the header is an 8-pin
socket that plugs into the user’s target via the 8-pin
stand-off connector.
When the ICD pin on the PIC12F675-ICD device is
held low, the In-Circuit Debugger functionality is
enabled. This function allows simple debugging
functions when used with MPLAB ICD 2. When the
microcontroller has this feature enabled, some of the
resources are not available for general use. Table 9-10
shows
background debugger:
TABLE 9-10:
For more information, see 8-Pin MPLAB ICD 2 Header
Information Sheet (DS51292) available on Microchip’s
website (www.microchip.com).
External
Connector
Signals
Data I/O
Program Memory
CLK
+5V
V
which
In-Circuit Debugger
0V
PP
I/O pins
Stack
PIC12F629/675
features
DEBUGGER RESOURCES
To Normal
Connections
To Normal
Connections
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
are
Address 0h must be NOP
®
ICD 2 development with
ICDCLK, ICDDATA
consumed
300h - 3FEh
V
V
GP3/MCLR/V
GP1
GP0
V
DS41190C-page 67
PIC12F629/675
DD
SS
DD
1 level
by
PP
the