PIC18LF2523-I/SP Microchip Technology, PIC18LF2523-I/SP Datasheet - Page 205

• Manufacturer Part Number: PIC18LF2523-I/SP
• Description: IC PIC MCU FLASH 16KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF2523-I/SP

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SPI/USART
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.4.17.3
Bus collision occurs during a Stop condition if:
a)
b)
FIGURE 17-33:
FIGURE 17-34:
© 2007 Microchip Technology Inc.
After the SDA pin has been deasserted and
allowed to float high, SDA is sampled low after
the BRG has timed out.
After the SCL pin is deasserted, SCL is sampled
low before SDA goes high.
SDA
SCL
PEN
BCLIF
P
SSPIF
SDA
SCL
PEN
BCLIF
P
SSPIF
Bus Collision During a Stop
Condition
BUS COLLISION DURING A STOP CONDITION (CASE 1)
BUS COLLISION DURING A STOP CONDITION (CASE 2)
SDA asserted low
Assert SDA
T
BRG
T
BRG
PIC18F2423/2523/4423/4523
Preliminary
T
BRG
T
BRG
The Stop condition begins with SDA asserted low.
When SDA is sampled low, the SCL pin is allowed to
float. When the pin is sampled high (clock arbitration),
the Baud Rate Generator is loaded with SSPADD<6:0>
and counts down to 0. After the BRG times out, SDA is
sampled. If SDA is sampled low, a bus collision has
occurred. This is due to another master attempting to
drive a data ‘0’ (Figure 17-33). If the SCL pin is
sampled low before SDA is allowed to float high, a bus
collision occurs. This is another case of another master
attempting to drive a data ‘0’ (Figure 17-34).
SCL goes low before SDA goes high,
set BCLIF
T
BRG
T
BRG
SDA sampled
low after T
set BCLIF
‘0’
‘0’
DS39755B-page 203
‘0’
‘0’
BRG
,