DSPIC30F5016-30I/PT Microchip Technology, DSPIC30F5016-30I/PT Datasheet - Page 175

• Manufacturer Part Number: DSPIC30F5016-30I/PT
• Description: IC DSPIC MCU/DSP 66K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F5016-30I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 66KB (22K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 68
• Flash Memory Size: 66KB
• Supply Voltage Range: 2.5V To 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164320 - MODULE SKT MPLAB PM3 80TQFPAC30F007 - MODULE SKT FOR DSPIC30F 80TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F501630IPT

24.0
This section provides an overview of dsPIC30F electrical characteristics. Additional information will be provided in future
revisions of this document as it becomes available.
For detailed information about the dsPIC30F architecture and core, refer to the “dsPIC30F Family Reference Manual”
(DS70046).
Absolute maximum ratings for the dsPIC30F family are listed below. Exposure to these maximum rating conditions for
extended periods may affect device reliability. Functional operation of the device at these or any other conditions above
the parameters indicated in the operation listings of this specification is not implied.
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to V
Voltage on V
Voltage on MCLR with respect to V
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports
© 2008 Microchip Technology Inc.
†
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
Note 1: Voltage spikes below V
2: Maximum allowable current is a function of device maximum power dissipation. See Table 24-6.
ELECTRICAL CHARACTERISTICS
Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/V
than pulling this pin directly to V
DD
with respect to V
IK
OK
(V
DD
SS
I
(V
< 0 or V
pin
O
pin ...........................................................................................................................300 mA
(2)
< 0 or V
...........................................................................................................................250 mA
SS
I
SS
SS
SS
> V
(†)
......................................................................................................... -0.3V to +5.5V
........................................................................................................ 0V to +13.25V
(2)
at the MCLR/V
O
(except V
DD
...............................................................................................................200 mA
> V
) .......................................................................................................... ±20 mA
SS
DD
.
) ................................................................................................... ±20 mA
DD
and MCLR)
PP
pin, inducing currents greater than 80 mA, may cause latch-up.
(1)
dsPIC30F5015/5016
............................................... -0.3V to (V
DS70149D-page 175
PP
DD
pin, rather
+ 0.3V)