STR715FR0T6 STMicroelectronics, STR715FR0T6 Datasheet - Page 20

• Manufacturer Part Number: STR715FR0T6
• Description: MCU 32BIT 64KB FLASH 64-LQFP
• Manufacturer: STMicroelectronics
• Series: STR7r

Specifications of STR715FR0T6

• Core Processor: ARM7
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: I²C, HDLC, Smartcard, SPI, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8 + 16K)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: STR715x
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MCBSTR7, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: STR710-SK/HIT, STR711-SK/IAR, STR712-SK/IAR, STR71X-SK/RAIS, STX-PRO/RAIS, STX-RLINK, STR79-RVDK/CPP, STR79-RVDK, STR79-RVDK/UPG
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 4 Channel
• For Use With: MCBSTR7UME - MCBSTR7 + ULINK-ME DEV KIT497-6412 - BOARD EVAL STPM01/STR715FR0MCBSTR7 - BOARD EVAL STM STR71X SERIES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-4888

System architecture
Table 4.
20/78
143
144
Pin n°
C4
B3
P0.8/U0.RX/
U0.TX
P0.9/U0.TX/
BOOT.0
STR710 pin description
1. The Reset configuration of the I/O Ports is IPUPD (input pull-up/pull down). Refer to
2. In reset state, these pins configured as Input PU/PD with weak pull-up enabled. They must be configured
3. In reset state, these pins configured as Input PU/PD with weak pull-down enabled to output Address
4. V
5. During the reset phase, these pins are in input pull-up state. When reset is released, they are configured as
6. During the reset phase, these pins are in input pull-up state. When reset is released, they are configured as
7. During the reset phase, these pins are in input pull-down state. When reset is released, they are configured
8. During the reset phase, this pin is in input floating state. When reset is released, it is configured as Output
Pin name
The Port bit configuration at reset is PC0=1, PC1=1, PC2=0. The port data register bit (PD) value depends
on the pu/pd column which specifies whether the pull-up or pull-down is enabled at reset
by software as Alternate Function (see
External Memory Interface.
0x0000 0000 using the External Memory Interface. To access memory banks greater than 1Mbyte, they
need to be configured by software as Alternate Function (see
page
Output Push-Pull.
Hi-Z.
as Output Push-Pull.
Push-Pull.
33IO-PLL
29).
and V
I/O pd C
I/O pd C
33
are internally connected. V
Input
T
T
X 4mA T
4mA X
Output
Table 8: Port bit configuration table on page
SSIO-PLL
X
and V
Note: This pin may be used for single wire UART
(half duplex) if programmed as Alternate Function
Output. The pin will be tri-stated except when
UART transmission is in progress
function
Port 0.8
Port 0.9
reset)
(after
Main
SS
Table 8: Port bit configuration table on
are internally connected.
UART0:
Receive Data
input
Select Boot
Configuration
input
Alternate function
29) to be used by the
Table 8 on page
UART0: Transmit
data output.
UART0: Transmit
data output
STR71xF
29.