C8051F804-GS Silicon Laboratories Inc, C8051F804-GS Datasheet - Page 123

• Manufacturer Part Number: C8051F804-GS
• Description: IC MCU 8BIT 16KB FLASH 16SOIC
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F80xr

Specifications of C8051F804-GS

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Cap Sense, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 13
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (3.9mm Width)
• Processor Series: C8051F8x
• Core: 8051
• Data Bus Width: 16 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F800DK
• Minimum Operating Temperature: - 55 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1773-5

21. Reset Sources
Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this
reset state, the following occur:




All SFRs are reset to the predefined values noted in the SFR detailed descriptions. The contents of internal
data memory are unaffected during a reset; any previously stored data is preserved. However, since the
stack pointer SFR is reset, the stack is effectively lost, even though the data on the stack is not altered.
The Port I/O latches are reset to 0xFF (all logic ones) in open-drain mode. Weak pullups are enabled dur-
ing and after the reset. For V
exits the reset state.
On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to the inter-
nal oscillator. The Watchdog Timer is enabled with the system clock divided by 12 as its clock source. Pro-
gram execution begins at location 0x0000.
CIP-51 halts program execution
Special Function Registers (SFRs) are initialized to their defined reset values
External Port pins are forced to a known state
Interrupts and timers are disabled.
Px.x
Px.x
System
Clock
Comparator 0
+
-
Detector
Missing
C0RSEF
Clock
(one-
shot)
Microcontroller
EN
Extended Interrupt
DD
CIP-51
Core
Handler
Monitor and power-on resets, the RST pin is driven low until the device
WDT
Figure 21.1. Reset Sources
PCA
EN
VDD
System Reset
Supply
Monitor
+
-
Rev. 1.0
Enable
(Software Reset)
SWRSF
'0'
Power On
Reset
Operation
C8051F80x-83x
FLASH
Errant
(wired-OR)
Reset
Funnel
RST
123