C8051F34A-GM Silicon Laboratories Inc, C8051F34A-GM Datasheet - Page 101

• Manufacturer Part Number: C8051F34A-GM
• Description: IC 8051 MCU 64K FLASH MEM 32-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F34A-GM

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4352 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 32QFN EP
• Device Core: 8051
• Family Name: C8051F34x
• Maximum Speed: 48 MHz
• Cpu Family: C8051F34x
• Device Core Size: 8b
• Frequency (max): 48MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 25
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1350-5

11.1. Power-On Reset
During power-up, the device is held in a reset state and the RST pin is driven low until V
V
typically less than 0.3 ms. Figure 11.2. plots the power-on and V
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. When PORSF is
set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is cleared by all other
resets). Since all resets cause program execution to begin at the same location (0x0000) software can
read the PORSF flag to determine if a power-up was the cause of reset. The content of internal data mem-
ory should be assumed to be undefined after a power-on reset. The V
power-on reset.
Software can force a power-on reset by writing ‘1’ to the PINRSF bit in register RSTSRC.
RST
. A Power-On Reset delay (T
Logic HIGH
Logic LOW
2.70
2.4
2.0
1.0
Figure 11.2. Power-On and V
RST
C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
V
RST
PORDelay
Power-On
Reset
) occurs before the device is released from reset; this delay is
T
PORDelay
Rev. 1.3
DD
Monitor Reset Timing
DD
Monitor
Reset
VDD
monitor reset timing.
DD
monitor is enabled following a
VDD
t
DD
settles above
101