M38869FFAHP#UU Renesas Electronics America, M38869FFAHP#UU Datasheet - Page 27

• Manufacturer Part Number: M38869FFAHP#UU
• Description: IC 740/3886 MCU FLASH 80LQFP
• Manufacturer: Renesas Electronics America
• Series: 740/38000r

Specifications of M38869FFAHP#UU

• Core Processor: 740
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SIO, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 64
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

TIMERS
The 3886 group has four timers: timer X, timer Y, timer 1, and
timer 2.
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
All timers are count down. When the timer reaches “00
derflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When a timer underflows, the interrupt request bit corresponding
to that timer is set to “1”.
Fig. 19 Structure of timer XY mode register
24
b 7
b 0
b 1 b 0
b 5 b 4
T i m e r X Y m o d e r e g i s t e r
( T M : a d d r e s s 0 0 2 3
T i m e r X o p e r a t i n g m o d e b i t
0 0 : T i m e r m o d e
0 1 : P u l s e o u t p u t m o d e
1 0 : E v e n t c o u n t e r m o d e
1 1 : P u l s e w i d t h m e a s u r e m e n t m o d e
C N T R
T i m e r X c o u n t s t o p b i t
T i m e r Y o p e r a t i n g m o d e b i t
0 0 : T i m e r m o d e
0 1 : P u l s e o u t p u t m o d e
1 0 : E v e n t c o u n t e r m o d e
1 1 : P u l s e w i d t h m e a s u r e m e n t m o d e
C N T R
T i m e r Y c o u n t s t o p b i t
1 : I n t e r r u p t a t r i s i n g e d g e
0 : C o u n t s t a r t
1 : I n t e r r u p t a t r i s i n g e d g e
0 : C o u n t s t a r t
1 : C o u n t s t o p
0 : I n t e r r u p t a t f a l l i n g e d g e
1 : C o u n t s t o p
0 : I n t e r r u p t a t f a l l i n g e d g e
C o u n t a t r i s i n g e d g e i n e v e n t
C o u n t a t f a l l i n g e d g e i n e v e n t
C o u n t a t r i s i n g e d g e i n e v e n t
C o u n t a t f a l l i n g e d g e i n e v e n t
c o u n t e r m o d e
c o u n t e r m o d e
c o u n t e r m o d e
c o u n t e r m o d e
0
1
a c t i v e e d g e s e l e c t i o n b i t
a c t i v e e d g e s e l e c t i o n b i t
1 6
)
16
”, an un-
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency di-
vided by 16. The output of prescaler 12 is counted by timer 1 and
timer 2, and a timer underflow sets the interrupt request bit.
Timer X and Timer Y
Timer X and Timer Y can each select in one of four operating
modes by setting the timer XY mode register.
(1) Timer Mode
The timer counts f(X
(2) Pulse Output Mode
Timer X (or timer Y) counts f(X
the timer reach “00
CNTR
lection bit is “0”, output begins at “ H”.
If it is “1”, output starts at “L”. When using a timer in this mode, set
the corresponding port P5
put mode.
(3) Event Counter Mode
Operation in event counter mode is the same as in timer mode,
except that the timer counts signals input through the CNTR
CNTR
When the CNTR
rising edge of the CNTR
When the CNTR
falling edge of the CNTR
(4) Pulse Width Measurement Mode
If the CNTR
counts f(X
CNTR
counts while the CNTR
The count can be stopped by setting “1” to the timer X (or timer Y)
count stop bit in any mode. The corresponding interrupt request
bit is set each time a timer overflows.
The count source for timer Y in the timer mode or the pulse output
mode can be selected from either f(X
Y count source selection bit of the port control register 2 (bit 5 of
address 002F
1
1
0
) pin is inverted. If the CNTR
pin.
(or CNTR
IN
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
0
)/16 while the CNTR
(or CNTR
16
).
0
0
(or CNTR
(or CNTR
1
) active edge selection bit is “1”, the timer
IN
16
MITSUBISHI MICROCOMPUTERS
)/16.
”, the signal output from the CNTR
0
1
0
) active edge selection bit is “0”, the timer
(or CNTR
0
(or CNTR
4
(or CNTR
( or port P5
1
1
) active edge selection bit is “0”, the
) active edge selection bit is “1”, the
IN
0
)/16. Whenever the contents of
1
(or CNTR
) pin is at “L”.
1
0
) pin is counted.
1
IN
) pin is counted.
(or CNTR
)/16 or f(X
5
) direction register to out-
3886 Group
1
) pin is at “H”. If the
1
) active edge se-
CIN
) by the timer
0
0
(or
or