PIC16F1826-E/P Microchip Technology, PIC16F1826-E/P Datasheet - Page 214

• Manufacturer Part Number: PIC16F1826-E/P
• Description: MCU PIC 8BIT 2K FLASH 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1826-E/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 32MHz
• No. Of Timers: 3
• Core: PIC
• Processor Series: PIC16F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 32 MHz
• Data Ram Size: 256 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 15
• Number Of Timers: 3
• Mounting Style: Through Hole
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 3.3 mm
• Interface Type: I2C, SPI, UART
• Length: 22.86 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.3 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F/LF1826/27
23.5.4
In Sleep mode, the TMRx register will not increment
and the state of the module will not change. If the CCPx
pin is driving a value, it will continue to drive that value.
When the device wakes up, TMRx will continue from its
previous state.
23.5.5
The PWM frequency is derived from the system clock
frequency. Any changes in the system clock frequency
will result in changes to the PWM frequency. See
Section 5.0 “Oscillator Module (With Fail-Safe
Clock Monitor)” for additional details.
23.5.6
Any Reset will force all ports to Input mode and the
CCP registers to their Reset states.
DS41391B-page 214
OPERATION IN SLEEP MODE
CHANGES IN SYSTEM CLOCK
FREQUENCY
EFFECTS OF RESET
Preliminary
23.5.7
The following steps should be taken when configuring
the CCP module for PWM operation:
1.
2.
3.
4.
5.
6.
• Clear the TMRxIF interrupt flag bit of the PIRx
• Configure the TxCKPS bits of the TxCON
• Enable Timerx by setting the TMRxON bit of
• Wait until Timerx overflows, TMRxIF bit of the
• Enable the PWM pin (CCPx) output driver(s) by
Note:
Disable the PWM pin (CCPx) output driver(s) by
setting the associated TRIS bit(s).
Load the PRx register with the PWM period value.
Configure the CCP module for the PWM mode
by loading the CCPxCON register with the
appropriate values.
Load the CCPRxL register and the DCxBx bits of
the CCPxCON register, with the PWM duty cycle
value.
Configure and start Timerx:
Enable PWM output pin:
register. See Note below.
register with the Timerx prescale value.
the T2CON register.
PIR1 register is set. See Note below.
clearing the associated TRIS bit(s).
SETUP FOR PWM OPERATION
In order to send a complete duty cycle and
period on the first PWM output, the above
steps must be included in the setup
sequence. If it is not critical to start with a
complete PWM signal on the first output,
then step 6 may be ignored.
© 2009 Microchip Technology Inc.