ATTINY2313V-10MUR Atmel, ATTINY2313V-10MUR Datasheet - Page 145
![MCU AVR 2KB FLASH 10MHZ 20QFN](/photos/6/87/68751/313-20-qfn_sml.jpg)
ATTINY2313V-10MUR
Manufacturer Part Number
ATTINY2313V-10MUR
Description
MCU AVR 2KB FLASH 10MHZ 20QFN
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY2313V-10MUR
Core Processor
AVR
Core Size
8-Bit
Speed
10MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
18
Program Memory Size
2KB (1K x 16)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
- Current page: 145 of 226
- Download datasheet (4Mb)
USI Status Register –
USISR
USI Control Register –
USICR
2543L–AVR–08/10
The Status Register contains interrupt flags, line status flags and the counter value.
• Bit 7 – USISIF: Start Condition Interrupt Flag
When Two-wire mode is selected, the USISIF flag is set (to one) when a start condition is
detected. When output disable mode or Three-wire mode is selected and (USICSx = 0b11 &
USICLK = 0) or (USICS = 0b10 & USICLK = 0), any edge on the SCK pin sets the flag.
An interrupt will be generated when the flag is set while the USISIE bit in USICR and the Global
Interrupt Enable Flag are set. The flag will only be cleared by writing a logical one to the USISIF
bit. Clearing this bit will release the start detection hold of USCL in Two-wire mode.
A start condition interrupt will wake-up the processor from all sleep modes.
• Bit 6 – USIOIF: Counter Overflow Interrupt Flag
This flag is set (one) when the 4-bit counter overflows (i.e., at the transition from 15 to 0). An
interrupt will be generated when the flag is set while the USIOIE bit in USICR and the Global
Interrupt Enable Flag are set. The flag will only be cleared if a one is written to the USIOIF bit.
Clearing this bit will release the counter overflow hold of SCL in Two-wire mode.
A counter overflow interrupt will wake-up the processor from Idle sleep mode.
• Bit 5 – USIPF: Stop Condition Flag
When Two-wire mode is selected, the USIPF flag is set (one) when a stop condition is detected.
The flag is cleared by writing a one to this bit. Note that this is not an interrupt flag. This signal is
useful when implementing Two-wire bus master arbitration.
• Bit 4 – USIDC: Data Output Collision
This bit is logical one when bit 7 in the Shift Register differs from the physical pin value. The flag
is only valid when Two-wire mode is used. This signal is useful when implementing Two-wire
bus master arbitration.
• Bits 3..0 – USICNT3..0: Counter Value
These bits reflect the current 4-bit counter value. The 4-bit counter value can directly be read or
written by the CPU.
The 4-bit counter increments by one for each clock generated either by the external clock edge
detector, by a Timer/Counter0 overflow, or by software using USICLK or USITC strobe bits. The
clock source depends of the setting of the USICS1..0 bits. For external clock operation a special
feature is added that allows the clock to be generated by writing to the USITC strobe bit. This
feature is enabled by write a one to the USICLK bit while setting an external clock source
(USICS1 = 1).
Note that even when no wire mode is selected (USIWM1..0 = 0) the external clock input
(USCK/SCL) are can still be used by the counter.
The Control Register includes interrupt enable control, wire mode setting, Clock Select setting,
and clock strobe.
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
USISIF
USISIE
R/W
R/W
7
0
7
0
USIOIF
USIOIE
R/W
6
0
R/W
6
0
USIPF
R/W
USIWM1
5
0
R/W
5
0
USIDC
USIWM0
R
4
0
R/W
4
0
USICNT3
R/W
3
0
USICS1
R/W
3
0
USICNT2
R/W
USICS0
2
0
R/W
2
0
USICNT1
R/W
USICLK
1
0
W
1
0
USICNT0
R/W
USITC
0
0
W
0
0
USISR
USICR
145
Related parts for ATTINY2313V-10MUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATTINY2313-20PI](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY2313-20SI](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20SOIC
Manufacturer:
Atmel
Datasheet:
![ATtiny2313](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATTINY2313-20MI](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
![ATTINY2313-20MU](/photos/6/87/68751/313-20-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20MLF
Manufacturer:
Atmel
Datasheet:
![ATTINY2313-20PU](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY2313-20SU](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY2313-20PJ](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY2313-20SJ](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY2313-20SUR](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY2313-20MUR](/photos/6/87/68751/313-20-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20WQFN
Manufacturer:
Atmel
Datasheet:
![ATTIny2313-16MI](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit AVR Microcontroller with 2K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
![attiny2313v](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Attiny2313 8-bit With 2k Bytes Of In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet: