PIC16C712-04/P Microchip Technology, PIC16C712-04/P Datasheet - Page 55
![IC MCU OTP 1KX14 A/D PWM 18DIP](/photos/6/76/67657/18-dip_300mil__sml.jpg)
PIC16C712-04/P
Manufacturer Part Number
PIC16C712-04/P
Description
IC MCU OTP 1KX14 A/D PWM 18DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16C716-04P.pdf
(106 pages)
2.PIC16C716-04P.pdf
(14 pages)
3.PIC16C712-04P.pdf
(109 pages)
Specifications of PIC16C712-04/P
Core Size
8-Bit
Program Memory Size
1.75KB (1K x 14)
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Core Processor
PIC
Speed
4MHz
Number Of I /o
13
Program Memory Type
OTP
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 4x8b
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Package / Case
18-DIP (0.300", 7.62mm)
Controller Family/series
PIC16C
No. Of I/o's
13
Ram Memory Size
128Byte
Cpu Speed
4MHz
No. Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Connectivity
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16C712-04/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
9.4
A Power-on Reset pulse is generated on-chip when
V
advantage of the POR, just tie the MCLR pin directly (or
through a resistor) to V
RC components usually needed to create a Power-on
Reset. A maximum rise time for V
(parameter D004). For a slow rise time, see Figure 9-5.
When the device starts normal operation (exits the
reset condition), device operating parameters (voltage,
frequency, temperature,...) must be met to ensure oper-
ation. If these conditions are not met, the device must
be held in reset until the operating conditions are met.
Brown-out Reset may be used to meet the start-up con-
ditions.
FIGURE 9-5:
DD
Note 1: External Power-on Reset circuit is required
1999 Microchip Technology Inc.
rise is detected (to a level of 1.5V - 2.1V). To take
2: R < 40 k is recommended to make sure
3: R1 = 100 to 1 k will limit any current
Power-On Reset (POR)
only if V
diode D helps discharge the capacitor
quickly when V
that voltage drop across R does not violate
the device’s electrical specification.
flowing into MCLR from external capacitor
C in the event of MCLR/V
down due to Electrostatic Discharge
(ESD) or Electrical Overstress (EOS).
V
DD
EXTERNAL POWER-ON
RESET CIRCUIT (FOR SLOW
V
DD
R
DD
C
V
power-up slope is too slow. The
DD
POWER-UP)
DD
DD
. This will eliminate external
R1
powers down.
PIC16C7XX
MCLR
PP
DD
pin break-
is specified
Preliminary
9.5
The Power-up Timer provides a fixed nominal time-out
(parameter #33), on power-up only, from the POR. The
Power-up Timer operates on an internal RC oscillator.
The chip is kept in reset as long as the PWRT is active.
The PWRT’s time delay allows V
able level. A configuration bit is provided to enable/dis-
able the PWRT.
The power-up time delay will vary from chip to chip due
to V
parameters for details.
9.6
The Oscillator Start-up Timer (OST) provides a 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over (parameter #32). This ensures that
the crystal oscillator or resonator has started and stabi-
lized.
The OST time-out is invoked only for XT, LP and HS
modes and only on Power-on Reset or wake-up from
SLEEP.
9.7
The PIC16C712/716 members have on-chip Brown-out
Reset circuitry. A configuration bit, BODEN, can disable
(if clear/programmed) or enable (if set) the Brown-out
Reset circuitry. If V
parameter D005(V
eter (T
reset the chip. A reset is not guaranteed to occur if V
falls below 4.0V for less than parameter (T
On any reset (Power-on, Brown-out, Watchdog, etc.)
the chip will remain in Reset until V
V
keep the chip in reset an additional 72 ms.
If V
running, the chip will go back into a Brown-out Reset
and the Power-up Timer will be re-initialized. Once V
rises above V
72 ms reset. The Power-up Timer should always be
enabled when Brown-out Reset is enabled. Figure 9-7
shows typical Brown-out situations.
For operations where the desired brown-out voltage is
other than 4V, an external brown-out circuit must be
used. Figure 9-8, 9-9 and 9-10 show examples of exter-
nal brown-out protection circuits.
BOR
DD
DD
. The Power-up Timer will now be invoked and will
BOR
drops below V
, temperature, and process variation. See DC
Power-up Timer (PWRT)
Oscillator Start-up Timer (OST)
Brown-Out Reset (BOD)
) in Table 12-6. The brown-out situation will
BOR
PIC16C712/716
, the Power-Up Timer will execute a
BOR
DD
BOR
) for a time greater than param-
falls below 4.0V, refer to V
while the Power-up Timer is
DD
to rise to an accept-
DS41106A-page 55
DD
BOR
rises above
).
BOR
DD
DD