ATTINY2313V-10SU Atmel, ATTINY2313V-10SU Datasheet - Page 33

• Manufacturer Part Number: ATTINY2313V-10SU
• Description: IC MCU AVR 2K FLASH 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313V-10SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 10MHz
• Interface Type: SPI/USART/USI
• Total Internal Ram Size: 128Byte
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 1.8V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: SOIC
• Package: 20SOIC
• Family Name: ATtiny
• Maximum Speed: 10 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Processor Series: ATTINY2x
• Core: AVR8
• Data Ram Size: 128 B
• Maximum Clock Frequency: 10 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AVR Tiny
• No. Of I/o's: 18
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 10MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

System Control
and Reset
Resetting the AVR
Reset Sources
2543L–AVR–08/10
During reset, all I/O Registers are set to their initial values, and the program starts execution
from the Reset Vector. The instruction placed at the Reset Vector must be an RJMP – Relative
Jump – instruction to the reset handling routine. If the program never enables an interrupt
source, the Interrupt Vectors are not used, and regular program code can be placed at these
locations. The circuit diagram in
parameters of the reset circuitry.
The I/O ports of the AVR are immediately reset to their initial state when a reset source goes
active. This does not require any clock source to be running.
After all reset sources have gone inactive, a delay counter is invoked, stretching the internal
reset. This allows the power to reach a stable level before normal operation starts. The time-out
period of the delay counter is defined by the user through the SUT and CKSEL Fuses. The dif-
ferent selections for the delay period are presented in
The ATtiny2313 has four sources of reset:
•
•
•
•
Figure 14. Reset Logic
Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset
threshold (V
External Reset. The MCU is reset when a low level is present on the RESET pin for longer
than the minimum pulse length.
Watchdog Reset. The MCU is reset when the Watchdog Timer period expires, the Watchdog
is enabled, and Watchdog Interrupt is disabled.
Brown-out Reset. The MCU is reset when the supply voltage V
Reset threshold (V
BODLEVEL [2..0]
POT
).
BOT
Pull-up Resistor
) and the Brown-out Detector is enabled.
FILTER
SPIKE
Figure 14
CKSEL[3:0]
Power-on Reset
Reset Circuit
SUT[1:0]
Brown-out
Watchdog
Oscillator
Generator
Circuit
Clock
shows the reset logic.
CK
Register (MCUSR)
MCU Status
DATA BUS
Delay Counters
“Clock Sources” on page
Table 15
CC
TIMEOUT
is below the Brown-out
defines the electrical
23.
33