PIC16LC554-04I/P Microchip Technology, PIC16LC554-04I/P Datasheet - Page 48
![IC MCU OTP 512X14 18DIP](/photos/6/76/67657/18-dip_300mil__sml.jpg)
PIC16LC554-04I/P
Manufacturer Part Number
PIC16LC554-04I/P
Description
IC MCU OTP 512X14 18DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheet
1.PIC16C554-04P.pdf
(108 pages)
Specifications of PIC16LC554-04I/P
Core Processor
PIC
Core Size
8-Bit
Speed
4MHz
Peripherals
POR, WDT
Number Of I /o
13
Program Memory Size
896B (512 x 14)
Program Memory Type
OTP
Ram Size
80 x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
18-DIP (0.300", 7.62mm)
Processor Series
PIC16LC
Core
PIC
Data Bus Width
8 bit
Data Ram Size
80 B
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
13
Number Of Timers
8
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
ICE2000
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Data Converters
-
Connectivity
-
Lead Free Status / Rohs Status
Details
PIC16C55X
6.9
If
programmed, the on-chip program memory can be
read out for verification purposes.
6.10
Four memory locations (2000h-2003h) are designated
as ID locations where the user can store checksum or
other code-identification numbers. These locations are
not accessible during normal execution but are
readable and writable during program/verify.
6.11
The PIC16C55X microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom
firmware to be programmed.
The device is placed into a Program/Verify mode by
holding the RB6 and RB7 pins low while raising the
MCLR (V
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After RESET, to place the device into Programming/
Verify mode, the program counter (PC) is at location
00h. A 6-bit command is then supplied to the device.
Depending on the command, 14 bits of program data
are then supplied to or from the device, depending if
the command was a load or a read. For complete
details of serial programming, please refer to the
PIC16C6X/7X Programming Specifications (Literature
#DS30228).
A typical in-circuit serial programming connection is
shown in Figure 6-15.
DS40143D-page 46
Note:
the
Code Protection
ID Locations
In-Circuit Serial Programming™
code
PP
Microchip does not recommend code
protecting windowed devices.
) pin from V
protection
IL
to V
bit(s)
IHH
(see programming
have
not
been
Preliminary
FIGURE 6-15:
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
PP
To Normal
Connections
To Normal
Connections
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
2002 Microchip Technology Inc.
V
V
MCLR/V
RB6
RB7
V
DD
SS
DD
PIC16C55X
PP