PIC16LF707-I/P Microchip Technology, PIC16LF707-I/P Datasheet - Page 164

• Manufacturer Part Number: PIC16LF707-I/P
• Description: MCU 8BIT 14KB FLASH 5.5V 40PDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF707-I/P

• Core Size: 8-Bit
• Program Memory Size: 14KB (8K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 36
• Program Memory Type: FLASH
• Ram Size: 363 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 14x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16LF
• No. Of I/o's: 36
• Ram Memory Size: 363Byte
• Cpu Speed: 20MHz
• No. Of Timers: 6
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: I2C, SPI, AUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 14 Channel
• On-chip Dac: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC16F707/PIC16LF707
REGISTER 19-1:
DS41418A-page 164
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3-0
Note 1:
WCOL
R/W-0
When enabled, these pins must be properly configured as input or output.
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in
0 = No collision
SSPOV: Receive Overflow Indicator bit
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
1 = Enables serial port and configures SCK, SDO and SDI as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
SSPM<3:0>: Synchronous Serial Port Mode Select bits
0000 = SPI Master mode, clock = F
0001 = SPI Master mode, clock = F
0010 = SPI Master mode, clock = F
0011 = SPI Master mode, clock = TMR2 output/2
0100 = SPI Slave mode, clock = SCK pin. SS pin control enabled.
0101 = SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.
SSPOV
R/W-0
software)
overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user must read
the SSPBUF, even if only transmitting data, to avoid setting overflow. In Master mode, the over-
flow bit is not set since each new reception (and transmission) is initiated by writing to the
SSPBUF register.
SSPCON: SYNC SERIAL PORT CONTROL REGISTER (SPI MODE)
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
R/W-0
CKP
Preliminary
OSC
OSC
OSC
/4
/16
/64
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
SSPM2
R/W-0
 2010 Microchip Technology Inc.
x = Bit is unknown
SSPM1
R/W-0
(1)
SSPM0
R/W-0
bit 0