DSPIC30F3013-20E/ML Microchip Technology, DSPIC30F3013-20E/ML Datasheet - Page 5
![IC DSPIC MCU/DSP 24K 44QFN](/photos/6/81/68122/150-44-qfn_sml.jpg)
DSPIC30F3013-20E/ML
Manufacturer Part Number
DSPIC30F3013-20E/ML
Description
IC DSPIC MCU/DSP 24K 44QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20ISO.pdf
(210 pages)
3.DSPIC30F2011-20ISO.pdf
(6 pages)
4.DSPIC30F2011-20IP.pdf
(26 pages)
5.DSPIC30F3012-20ISO.pdf
(14 pages)
6.DSPIC30F3012-20ISO.pdf
(20 pages)
Specifications of DSPIC30F3013-20E/ML
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
24KB (8K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 10x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
44-QFN
For Use With
DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Register 35-2:
© 2008 Microchip Technology Inc.
Upper Byte:
bit 15
bit 15-13 Unimplemented: Read as ‘0’
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4-2
Note 1: The SMP bit must be set only after setting the MSTEN bit. The SMP bit remains cleared if MSTEN = 0.
U-0
—
2: The CKE bit is not used in the Framed SPI modes. The user application should program this bit to ‘0’ for
DISSCK: Disable SCK1 Pin bit (SPI Master modes only)
1 = Internal SPI clock is disabled; pin functions as I/O
0 = Internal SPI clock is enabled
DISSDO: Disable SDO1 Pin bit
1 = SDO1 pin is not used by the module; pin functions as I/O
0 = SDO1 pin is controlled by the module
MODE16: Word/Byte Communication Select bit
1 = Communication is word-wide (16 bits)
0 = Communication is byte-wide (8 bits)
SMP: SPI1 Data Input Sample Phase bit
Master mode:
1 = Input data is sampled at the end of data output time
0 = Input data is sampled at the middle of data output time
Slave mode:
SMP must be cleared when SPI1 is used in Slave mode
CKE: SPI1 Clock Edge Select bit
1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6)
0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6)
SSEN: Slave Select Enable bit (Slave mode)
1 = SS1 pin is used for Slave mode
0 = SS1 pin is not used by module; pin is controlled by port function
CKP: Clock Polarity Select bit
1 = Idle state for clock is a high level; active state is a low level
0 = Idle state for clock is a low level; active state is a high level
MSTEN: Master Mode Enable bit
1 = Master mode
0 = Slave mode
SPRE<2:0>: Secondary Prescale bits (Master mode)
111 = Secondary prescale 1:1
110 = Secondary prescale 2:1
•
•
•
000 = Secondary prescale 8:1
the Framed SPI modes (FRMEN = 1).
U-0
—
SPI1CON1: SPI1 Control Register 1
Lower Byte:
bit 7
Section 35. Serial Peripheral Interface (SPI) (Part II)
R/W-0
SSEN
U-0
—
R/W-0
CKP
DISSCK
R/W-0
(2)
MSTEN
R/W-0
(1)
DISSDO
R/W-0
R/W-0
MODE16
R/W-0
SPRE<2:0>
R/W-0
SMP
R/W-0
(1)
R/W-0
CKE
R/W-0
(2)
bit 8
R/W-0
DS70272B-page 35-5
PPRE<1:0>
R/W-0
bit 0
35