PIC18F85J90-I/PT Microchip Technology, PIC18F85J90-I/PT Datasheet - Page 13

• Manufacturer Part Number: PIC18F85J90-I/PT
• Description: IC PIC MCU FLASH 16KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F85J90-I/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 67
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 67
• Ram Memory Size: 2KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 2
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: AUSART, EUSART, I2C, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 67
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM163030
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Package: 80TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

2.1
FIGURE 2-1:
© 2009 Microchip Technology Inc.
Note:
LINE_SHUNT2
LINE_SHUNT1
INPUT AND ANALOG FRONT END
(external to
PCB part of
meter case)
NEUTRAL
Shunt
FB = ferrite beads. Ferrite beads have an impedance of the
specified value at 100 MHz.
This meter comes populated with components designed for 220V line voltage. At the
bottom of the main board are the high voltage line and neutral connections. There are
four total connections that are made from the PCB to the meter casing, labeled as
LINE, NEUTRAL, SHUNT1 and SHUNT2. The shunt sits on the high or line side of a
two wire system and the meter employes a hot or “live” ground. The wires going into
the shunt to SHUNT1 and SHUNT2 should be twisted together. The wires going into
the LINE and NEUTRAL side of the meter should also be twisted together and kept
away from the SHUNT1 and SHUNT2 wires if possible.
The neutral side of the 2-wire system goes into a resistor divider on the voltage channel
input. Anti-aliasing low-pass filters will be included on both differential channels. The
voltage channel uses two 332 kΩ resistors to achieve a divider ratio of 664:1. For a line
voltage of 230 V
channel of each phase uses current transformer with a turns ratio of 2000:1 and burden
resistance of 56.4 kΩ. The resulting channel 0 signal size is 340 mV
twice the rated maximum current of the meter, still within the input range of the A/D
converter of the MCP3909.
Analog Front End, Phase A Connections and Reference Designators shown.
150 FB (Note)
150 FB (Note)
332 kΩ 332 kΩ
Chapter 2. Hardware
RMS
MCP3909/PIC18F85J90 SINGLE PHASE
ENERGY METER REFERENCE DESIGN
, the channel 1 input signal size will be 490 mV
10 step optional
resistor
ladder
1.0 kΩ
1.0 kΩ
1.0 kΩ
1.0 kΩ
0Ω
68 nF
68 nF
68 nF
68 nF
CH0-
CH0+
CH1+
PEAK
CH1+
MCP3909
PEAK
DS51884A-page 13
. The current
for 20A, or