PIC18F27J13-I/ML Microchip Technology, PIC18F27J13-I/ML Datasheet - Page 429

• Manufacturer Part Number: PIC18F27J13-I/ML
• Description: IC PIC MCU 128KB FLASH 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J13-I/ML

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Digital Ic Case Style: QFN
• Supply Voltage Range: 1.8V To 5.5V
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: I2C, SPI, EUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 19
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: DM164128, DM180021, DM183026-2, DV164131, MA180030, DM183022, DM183032, DV164136, MA180024
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180030 - BOARD DEMO PIC18F47J13 FS USBMA180029 - BOARD DEMO PIC18F47J53 FS USB
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

FIGURE 27-4:
Clock failure is tested for on the falling edge of the
sample clock. If a sample clock falling edge occurs
while the clock monitor is still set, and a clock failure
has been detected (Figure 27-5), the following results:
• The FSCM generates an oscillator fail interrupt by
• The device clock source is switched to the internal
• The WDT is reset.
During switchover, the postscaler frequency from the
internal oscillator block may not be sufficiently stable
for timing-sensitive applications. In these cases, it may
FIGURE 27-5:
 2010 Microchip Technology Inc.
setting bit, OSCFIF (PIR2<7>);
oscillator block (OSCCON is not updated to show
the current clock source – this is the fail-safe
condition); and
Peripheral
Source
(32 s)
INTRC
Clock
Note:
Sample Clock
Clock Monitor
Output (Q)
OSCFIF
Device
Output
Clock
(2.048 ms)
The device clock is normally at a much higher frequency than the sample clock. The relative frequencies in
this example have been chosen for clarity.
488 Hz
÷ 64
FSCM BLOCK DIAGRAM
FSCM TIMING DIAGRAM
(edge-triggered)
Clock Monitor
C
S
Latch
Clock Monitor Test
Q
Q
Detected
Failure
Clock
Preliminary
PIC18F47J13 FAMILY
Clock Monitor Test
be desirable to select another clock configuration and
enter an alternate power-managed mode. This can be
done to attempt a partial recovery or execute a
controlled shutdown. See Section 4.1.4 “Multiple
Sleep Commands” and Section 27.4.1 “Special
Considerations For Using Two-speed Start-up” for
more details.
The FSCM will detect failures of the primary or secondary
clock sources only. If the internal oscillator block fails, no
failure would be detected, nor would any action be
possible.
27.5.1
Both the FSCM and the WDT are clocked by the
INTRC oscillator. Since the WDT operates with a
separate divider and counter, disabling the WDT has
no effect on the operation of the INTRC oscillator when
the FSCM is enabled.
As already noted, the clock source is switched to the
INTRC clock when a clock failure is detected; this may
mean a substantial change in the speed of code execu-
tion. If the WDT is enabled with a small prescale value,
a decrease in clock speed allows a WDT time-out to
occur and a subsequent device Reset. For this reason,
Fail-Safe Clock Monitor events also reset the WDT and
postscaler, allowing it to start timing from when execu-
tion speed was changed and decreasing the likelihood
of an erroneous time-out.
Oscillator
Failure
FSCM AND THE WATCHDOG TIMER
Detected
Clock Monitor Test
Failure
DS39974A-page 429