ATMEGA64L-8MQR Atmel, ATMEGA64L-8MQR Datasheet - Page 5
![MCU AVR 64KB FLASH 8MHZ 64QFN](/photos/12/13/121326/313-64-qfn_sml.jpg)
ATMEGA64L-8MQR
Manufacturer Part Number
ATMEGA64L-8MQR
Description
MCU AVR 64KB FLASH 8MHZ 64QFN
Manufacturer
Atmel
Series
AVR® ATmegar
Specifications of ATMEGA64L-8MQR
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
53
Program Memory Size
64KB (32K x 16)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ATmega103
Compatibility Mode
Pin Descriptions
VCC
GND
Port A (PA7..PA0)
Port B (PB7..PB0)
2490QS–AVR–07/10
By programming the M103C Fuse, the ATmega64 will be compatible with the ATmega103
regards to RAM, I/O pins and Interrupt Vectors as described above. However, some new fea-
tures in ATmega64 are not available in this compatibility mode, these features are listed below:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Digital supply voltage.
Ground.
Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port A output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port A pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port A also serves the functions of various special features of the ATmega64 as listed on
73.
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port B output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port B also serves the functions of various special features of the ATmega64 as listed on
74.
One USART instead of two, asynchronous mode only. Only the eight least significant bits of
the Baud Rate Register is available.
One 16 bits Timer/Counter with two compare registers instead of two 16 bits Timer/Counters
with three compare registers.
Two-wire serial interface is not supported.
Port G serves alternate functions only (not a general I/O port).
Port F serves as digital input only in addition to analog input to the ADC.
Boot Loader capabilities is not supported.
It is not possible to adjust the frequency of the internal calibrated RC Oscillator.
The External Memory Interface can not release any Address pins for general I/O, neither
configure different wait states to different External Memory Address sections.
Only EXTRF and PORF exist in the MCUCSR Register.
No timed sequence is required for Watchdog Timeout change.
Only low-level external interrupts can be used on four of the eight External Interrupt sources.
Port C is output only.
USART has no FIFO buffer, so Data OverRun comes earlier.
The user must have set unused I/O bits to 0 in ATmega103 programs.
ATmega64(L)
page
page
5