DSPIC30F5013-20E/PT Microchip Technology, DSPIC30F5013-20E/PT Datasheet - Page 163

• Manufacturer Part Number: DSPIC30F5013-20E/PT
• Description: IC DSPIC MCU/DSP 66K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F5013-20E/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 66KB (22K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TFQFP
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPDM300004-2 - BOARD DEMO DSPICDEM.NET 2DM300004-1 - BOARD DEMO DSPICDEM.NET 1AC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DSPIC30F5013-20EP

23.0
This section provides an overview of dsPIC30F electrical characteristics. Additional information will be provided in future
revisions of this document as it becomes available.
For detailed information about the dsPIC30F architecture and core, refer to the ”dsPIC30F Family Reference Manual”
(DS70046).
Absolute maximum ratings for the dsPIC30F family are listed below. Exposure to these maximum rating conditions for
extended periods may affect device reliability. Functional operation of the device at these or any other conditions above
the parameters indicated in the operation listings of this specification is not implied.
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to V
Voltage on V
Voltage on MCLR with respect to V
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports
Note 1:
© 2011 Microchip Technology Inc.
†
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
Note:
2:
ELECTRICAL CHARACTERISTICS
Voltage spikes below V
Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/V
than pulling this pin directly to V
Maximum allowable current is a function of device maximum power dissipation. See
All peripheral electrical characteristics are specified. For exact peripherals available on specific devices,
please refer to the dsPIC30F5011/5013 Controller Family table. See
DD
with respect to V
IK
OK
(V
DD
SS
I
(V
< 0 or V
pin
O
pin ...........................................................................................................................300 mA
< 0 or V
(2)
SS
..........................................................................................................................250 mA
SS
I
SS
SS
> V
(†)
......................................................................................................... -0.3V to +5.5V
at the MCLR/V
....................................................................................................... 0V to +13.25V
O
(2)
(except V
DD
> V
..............................................................................................................200 mA
) .......................................................................................................... ±20 mA
SS
DD
.
) ................................................................................................... ±20 mA
DD
and MCLR)
PP
pin, inducing currents greater than 80 mA, may cause latchup.
(1)
............................................... -0.3V to (V
dsPIC30F5011/5013
Table 1
Table 23-2
DS70116J-page 163
PP
for P
pin, rather
DD
+ 0.3V)
DMAX
.