ATMEGA640-16CU Atmel, ATMEGA640-16CU Datasheet - Page 56

• Manufacturer Part Number: ATMEGA640-16CU
• Description: IC MCU AVR 64K FLASH 100-CBGA
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA640-16CU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.10 Register Description
10.10.1
10.10.2
2549M–AVR–09/10
SMCR – Sleep Mode Control Register
PRR0 – Power Reduction Register 0
There are three alternative ways to disable the OCD system:
•
•
•
The Sleep Mode Control Register contains control bits for power management.
• Bits 3, 2, 1 – SM2:0: Sleep Mode Select Bits 2, 1, and 0
These bits select between the five available sleep modes as shown in
Table 10-2.
Note:
• Bit 1 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
• Bit 7 - PRTWI: Power Reduction TWI
Writing a logic one to this bit shuts down the TWI by stopping the clock to the module. When
waking up the TWI again, the TWI should be re initialized to ensure proper operation.
Bit
0x33 (0x53)
Read/Write
Initial Value
Bit
(0x64)
Read/Write
Initial Value
Disable the OCDEN Fuse.
Disable the JTAGEN Fuse.
Write one to the JTD bit in MCUCR.
SM2
0
0
0
0
1
1
1
1
1. Standby modes are only recommended for use with external crystals or resonators.
PRTWI
Sleep Mode Select
R/W
7
0
7
–
R
0
SM1
0
0
1
1
0
0
1
1
PRTIM2
R/W
6
0
6
–
R
0
ATmega640/1280/1281/2560/2561
PRTIM0
R/W
5
0
R
5
–
0
SM0
0
1
0
1
0
1
0
1
R
4
–
0
R
4
–
0
PRTIM1
R/W
3
0
SM2
R/W
3
0
PRSPI
R/W
2
0
ADC Noise Reduction
SM1
R/W
Extended Standby
2
0
Sleep Mode
Power-down
Power-save
Standby
Reserved
Reserved
PRUSART0
Idle
SM0
R/W
Table
R/W
1
0
1
0
(1)
10-2.
(1)
R/W
SE
PRADC
0
0
R/W
0
0
SMCR
PRR0
56