PIC18LF8621-I/PT Microchip Technology, PIC18LF8621-I/PT Datasheet - Page 83

• Manufacturer Part Number: PIC18LF8621-I/PT
• Description: IC PIC MCU FLASH 32KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF8621-I/PT

• Core Size: 8-Bit
• Program Memory Size: 64KB (32K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 70
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3840Byte
• Cpu Speed: 40MHz
• No. Of Timers: 5
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3840 B
• Interface Type: MSSP, SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 2 x 8 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

7.3
To read a data memory location, the user must write the
address to the EEADRH:EEADR register pair, clear the
EEPGD control bit (EECON1<7>), clear the CFGS
EXAMPLE 7-1:
7.4
To write an EEPROM data location, the address must
first be written to the EEADRH:EEADR register pair
and the data written to the EEDATA register. Then the
sequence in Example 7-2 must be followed to initiate
the write cycle.
The write will not initiate if the above sequence is not
exactly followed (write 55h to EECON2, write AAh to
EECON2, then set WR bit) for each byte. It is strongly
recommended that interrupts be disabled during this
code segment.
Additionally, the WREN bit in EECON1 must be set to
enable writes. This mechanism prevents accidental
writes to data EEPROM due to unexpected code
EXAMPLE 7-2:
 2005 Microchip Technology Inc.
MOVLW DATA_EE_ADDRH
MOVWF EEADRH
MOVLW DATA_EE_ADDR
MOVWF EEADR
BCF
BCF
BSF
MOVF
Required
Sequence
Reading the Data EEPROM
Memory
Writing to the Data EEPROM
Memory
EECON1, EEPGD
EECON1, CFGS
EECON1, RD
EEDATA, W
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
BCF
BCF
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
BCF
DATA EEPROM READ
DATA EEPROM WRITE
DATA_EE_ADDRH
EEADRH
DATA_EE_ADDR
EEADR
DATA_EE_DATA
EEDATA
EECON1, EEPGD
EECON1, CFGS
EECON1, WREN
INTCON, GIE
0x55
EECON2
0xAA
EECON2
EECON1, WR
INTCON, GIE
EECON1, WREN
;
; Upper bits of Data Memory Address to read
;
; Lower bits of Data Memory Address to read
; Point to DATA memory
; Access EEPROM
; EEPROM Read
; W = EEDATA
PIC18F6525/6621/8525/8621
;
; Upper bits of Data Memory Address to write
;
; Lower bits of Data Memory Address to write
;
; Data Memory Value to write
; Point to DATA memory
; Access EEPROM
; Enable writes
; Disable Interrupts
;
; Write 55h
;
; Write AAh
; Set WR bit to begin write
; Enable Interrupts
; User code execution
; Disable writes on write complete (EEIF set)
control bit (EECON1<6>) and then set the RD control
bit (EECON1<0>). The data is available for the very
next instruction cycle; therefore, the EEDATA register
can be read by the next instruction. EEDATA will hold
this value until another read operation or until it is
written to by the user (during a write operation).
execution (i.e., runaway programs). The WREN bit
should be kept clear at all times except when updating
the EEPROM. The WREN bit is not cleared
by hardware.
After a write sequence has been initiated, EECON1,
EEADRH, EEADR and EEDATA cannot be modified.
The WR bit will be inhibited from being set unless the
WREN bit is set. Both WR and WREN cannot be set
with the same instruction.
At the completion of the write cycle, the WR bit is
cleared in hardware and the EEPROM Write Complete
Interrupt Flag bit (EEIF) is set. The user may either
enable this interrupt or poll this bit. EEIF must be
cleared by software.
DS39612B-page 81