AT90CAN128-15AZ Atmel, AT90CAN128-15AZ Datasheet - Page 348

• Manufacturer Part Number: AT90CAN128-15AZ
• Description: MCU AVR 128K FLASH 15MHZ 64TQFP
• Manufacturer: Atmel
• Series: AVR® 90CANr

Specifications of AT90CAN128-15AZ

• Package / Case: 64-TQFP, 64-VQFP
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 53
• Eeprom Size: 4K x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Program Memory Size: 128KB (128K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: CAN, I²C, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: AT90CANx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: CAN, SPI, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATDVK90CAN1, ATADAPCAN01
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: 90C
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

25.6.13
25.6.14
25.7
25.7.1
348
SPI Serial Programming Overview
AT90CAN32/64/128
Reading the Signature Bytes
Reading the Calibration Byte
Signal Names
Figure 25-6. Mapping Between BS1, BS2 and the Fuse and Lock Bits During Read
The algorithm for reading the Signature bytes is as follows (refer to
page 342
The algorithm for reading the Calibration byte is as follows (refer to
page 342
This section describes how to serial program and verify Flash Program memory, EEPROM Data
memory, Memory Lock bits, and Fuse bits in the AT90CAN32/64/128.
Both the Flash and EEPROM memory arrays can be programmed using the serial SPI bus while
RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input) and MISO (out-
put). After RESET is set low, the Programming Enable instruction needs to be executed first
before program/erase operations can be executed. NOTE, in
mapping for SPI programming is listed. Not all parts use the SPI pins dedicated for the internal
SPI interface. Note that throughout the description about Serial downloading, MOSI and MISO
are used to describe the serial data in and serial data out respectively. For AT90CAN32/64/128
these pins are mapped to PDI (PE0) and PDO (PE1).
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte (0x00 - 0x02).
3. Set OE to “0”, and BS1 to “0”. The selected Signature byte can now be read at DATA.
4. Set OE to “1”.
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte, 0x00.
3. Set OE to “0”, and BS1 to “1”. The Calibration byte can now be read at DATA.
4. Set OE to “1”.
for details on Command and Address loading):
for details on Command and Address loading):
Extended Fuse Byte
Fuse High Byte
Fuse Low Byte
Lock Bits
BS2
BS2
0
1
0
1
BS1
Table 25-13 on page
0
1
“Programming the Flash” on
“Programming the Flash” on
DATA
7679H–CAN–08/08
349, the pin