AT90CAN128-15AZ Atmel, AT90CAN128-15AZ Datasheet - Page 46

• Manufacturer Part Number: AT90CAN128-15AZ
• Description: MCU AVR 128K FLASH 15MHZ 64TQFP
• Manufacturer: Atmel
• Series: AVR® 90CANr

Specifications of AT90CAN128-15AZ

• Package / Case: 64-TQFP, 64-VQFP
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 53
• Eeprom Size: 4K x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Program Memory Size: 128KB (128K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: CAN, I²C, SPI, UART/USART
• Core Size: 8-Bit
• Processor Series: AT90CANx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: CAN, SPI, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATDVK90CAN1, ATADAPCAN01
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: 90C
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 53
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6. Power Management and Sleep Modes
6.0.1
46
AT90CAN32/64/128
Sleep Mode Control Register – SMCR
Sleep modes enable the application to shut down unused modules in the MCU, thereby saving
power. The AVR provides various sleep modes allowing the user to tailor the power consump-
tion to the application’s requirements.
To enter any of the five sleep modes, the SE bit in SMCR must be written to logic one and a
SLEEP instruction must be executed. The SM2, SM1, and SM0 bits in the SMCR Register select
which sleep mode (Idle, ADC Noise Reduction, Power-down, Power-save, or Standby) will be
activated by the SLEEP instruction. See
while the MCU is in a sleep mode, the MCU wakes up. The MCU is then halted for four cycles in
addition to the start-up time, executes the interrupt routine, and resumes execution from the
instruction following SLEEP. The contents of the register file and SRAM are unaltered when the
device wakes up from sleep. If a reset occurs during sleep mode, the MCU wakes up and exe-
cutes from the Reset Vector.
Figure 5-1 on page 37
distribution. The figure is helpful in selecting an appropriate sleep mode.
The Sleep Mode Control Register contains control bits for power management.
• Bit 7..4 – Reserved Bits
These bits are reserved for future use.
• Bits 3..1 – SM2..0: Sleep Mode Select Bits 2, 1, and 0
These bits select between the five available sleep modes as shown in
Table 6-1.
Note:
• Bit 1 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
Bit
Read/Write
Initial Value
SM2
0
0
0
0
1
1
1
1
1. Standby mode is only recommended for use with external crystals or resonators.
Sleep Mode Select
R
7
–
0
SM1
0
0
1
1
0
0
1
1
presents the different clock systems in the AT90CAN32/64/128, and their
R
6
–
0
R
5
–
0
SM0
0
1
0
1
0
1
0
1
Table 6-1
R
4
–
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Power-save
Reserved
Reserved
Standby
Reserved
SM2
R/W
3
0
for a summary. If an enabled interrupt occurs
(1)
SM1
R/W
2
0
SM0
R/W
1
0
Table
R/W
SE
0
0
6-1.
SMCR
7679H–CAN–08/08