W77E058A40DL Nuvoton Technology Corporation of America, W77E058A40DL Datasheet - Page 45

• Manufacturer Part Number: W77E058A40DL
• Description: IC MCU 8-BIT 32K FLASH 40-DIP
• Manufacturer: Nuvoton Technology Corporation of America
• Series: W77r

Specifications of W77E058A40DL

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, Serial Port
• Peripherals: POR, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP
• Cpu Family: W77
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: UART
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

W77E058A
The selection of instruction rate is going to take effect after a delay of one instruction cycle. Switching
to divide by 64 or 1024 mode must first go from divide by 4 mode. This means software can not switch
directly between clock/64 and clock/1024 mode. The CPU has to return clock/4 mode first, then go to
clock/64 or clock/1024 mode.
The W77E058 allows the user to use internal RC oscillator instead of external crystal. Setting the
XT/ RG bit (EXIF.3) selects the crystal or RC oscillator as the clock source. When invoking RC
oscillator in Economy mode, software may set the XTOFF bit to turn off the crystal amplifier for saving
power. The CPU would run at the clock rate of approximately 2−4 MHz divided by 4, 64 or 1024. The
RC oscillator is not precise so that can not be invoked to the operation which needs the accurate time-
base such as serial communication. The RGMD(EXIF.2) indicates current clock source. When
switching the clock source, CPU needs one instruction cycle delay to take effect new setting. If crystal
amplifier is disabled and RC oscillator is present clock source, software must first clear the XTOFF bit
to turn on crystal amplifier before switch to crystal operation. Hardware will set the XTUP bit
(STATUS.4) once the crystal is warm-up and ready for use. It is unable to set XT/ RG bit to 1 if XTUP
= 0.
In Economy mode, the serial port can not receive/transmit data correctly because the baud rate is
changed. In some systems, the external interrupts may require the fastest process such that the
reducing of operating speed is restricted. In order to solve these dilemmas, the W77E058 offers a
switchback feature which allows the CPU back to clock/4 mode immediately when triggered by serial
operation or external interrupts. The switchback feature is enabled by setting the SWB bit (PMR.5). A
serial port reception/transmission or qualified external interrupt which is enabled and acknowledged
without block conditions will cause CPU to return to divide by 4 mode. For the serial port reception, a
switchback is generated by a falling edge associated with start bit if the serial port reception is
enabled. When a serial port transmission, an instruction which writes a byte of data to serial port buffer
will cause a switchback to ensure the correct transmission. The switchback feature is unaffected by
serial port interrupt flags. After a switchback is generated, the software can manually return the CPU
to Economy mode. Note that the modification of clock control bits CD0 and CD1 will be ignored during
serial port transmit/receive when switchback is enabled. The Watchdog timer reset, power-on/fail reset
or external reset will force the CPU to return to divide by 4 mode.
9.3
Power Down Mode
The device can be put into Power Down mode by writing 1 to bit PCON.1. The instruction that does
this will be the last instruction to be executed before the device goes into Power Down mode. In the
Power Down mode, all the clocks are stopped and the device comes to a halt. All activity is completely
stopped and the power consumption is reduced to the lowest possible value. In this state the ALE and
PSEN pins are pulled low. The port pins output the values held by their respective SFRs.
The W77E058 will exit the Power Down mode with a reset or by an external interrupt pin enabled as
either level or edge detect. An external reset can be used to exit the Power down state. The high on
RST pin terminates the Power Down mode, and restarts the clock. The program execution will restart
from 0000h. In the Power down mode, the clock is stopped, so the Watchdog timer cannot be used to
provide the reset to exit Power down mode.
The W77E058 can be woken from the Power Down mode by forcing an external interrupt pin
activated, provided the corresponding interrupt is enabled, while the global enable(EA) bit is set. If
these conditions are met, then the low level on the external pin re-starts the oscillator. Then device
executes the interrupt service routine for the corresponding external interrupt. After the interrupt
service routine is completed, the program execution returns to the instruction after the one which put
Publication Release Date: April 17, 2007
- 45 -
Revision A10