MC9S12C64CFUE Freescale Semiconductor, MC9S12C64CFUE Datasheet - Page 314

• Manufacturer Part Number: MC9S12C64CFUE
• Description: IC MCU 64K FLASH 4K RAM 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C64CFUE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Processor Series: S12C
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 4 KB
• Interface Type: CAN/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 80PQFP
• Family Name: HCS12
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 2.5|5 V
• Height: 2.4 mm
• Length: 14 mm
• Supply Voltage (max): 2.75 V, 5.5 V
• Supply Voltage (min): 2.35 V, 2.97 V
• Width: 14 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 10 Freescale’s Scalable Controller Area Network (S12MSCANV2)
10.3.3
The following section details the organization of the receive and transmit message buffers and the
associated control registers.
To simplify the programmer interface, the receive and transmit message buffers have the same outline.
Each message buffer allocates 16 bytes in the memory map containing a 13 byte data structure.
An additional transmit buffer priority register (TBPR) is defined for the transmit buffers. Within the last
two bytes of this memory map, the MSCAN stores a special 16-bit time stamp, which is sampled from an
internal timer after successful transmission or reception of a message. This feature is only available for
transmit and receiver buffers, if the TIME bit is set (see
(CANCTL0)”).
The time stamp register is written by the MSCAN. The CPU can only read these registers.
Figure 10-23
identifiers. The mapping of standard identifiers into the IDR registers is shown in
All bits of the receive and transmit buffers are ‘x’ out of reset because of RAM-based implementation
All reserved or unused bits of the receive and transmit buffers always read ‘x’.
1. Exception: The transmit priority registers are 0 out of reset.
314
1. Not applicable for receive buffers
2. Read-only for CPU
3. Read-only for CPU
Address
0x00XA
0x00XB
0x00XC
0x00XD
0x00XE
0x00X0
0x00X1
0x00X2
0x00X3
0x00X4
0x00X5
0x00X6
0x00X7
0x00X8
0x00X9
0x00XF
Offset
Programmer’s Model of Message Storage
shows the common 13-byte data structure of receive and transmit buffers for extended
Identifier Register 0
Identifier Register 1
Identifier Register 2
Identifier Register 3
Data Segment Register 0
Data Segment Register 1
Data Segment Register 2
Data Segment Register 3
Data Segment Register 4
Data Segment Register 5
Data Segment Register 6
Data Segment Register 7
Data Length Register
Transmit Buffer Priority Register
Time Stamp Register (High Byte)
Time Stamp Register (Low Byte)
Table 10-23. Message Buffer Organization
MC9S12C-Family / MC9S12GC-Family
(1)
(3)
(2)
Rev 01.24
Register
Section 10.3.2.1, “MSCAN Control Register 0
Figure
Freescale Semiconductor
Access
10-24.
1
.