MC68331CEH25 Freescale Semiconductor, MC68331CEH25 Datasheet - Page 68

• Manufacturer Part Number: MC68331CEH25
• Description: IC MCU 32BIT 25MHZ 132-PQFP
• Manufacturer: Freescale Semiconductor
• Series: M683xxr

Specifications of MC68331CEH25

• Core Processor: CPU32
• Core Size: 32-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Type: ROMless
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 132-QFP
• Controller Family/series: 68K
• No. Of I/o's: 18
• Cpu Speed: 25MHz
• No. Of Timers: 1
• Embedded Interface Type: QSPI, SCI, UART
• No. Of Pwm Channels: 2
• Digital Ic Case Style: PQFP
• Rohs Compliant: Yes
• Processor Series: M683xx
• Core: CPU32
• Data Bus Width: 32 bit
• Data Ram Size: 80 B
• Interface Type: QSPI, SCI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Eeprom Size: -
• Ram Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

RWU — Receiver Wakeup
SBK — Send Break
SCSR — SCI Status Register
TDRE — Transmit Data Register Empty Flag
TC — Transmit Complete Flag
RDRF — Receive Data Register Full Flag
68
RESET:
15
Setting RWU enables the wakeup function, which allows the SCI to ignore received data until awakened
by either an idle line or address mark (as determined by WAKE). When in wakeup mode, the receiver
status flags are not set, and interrupts are inhibited. This bit is cleared automatically (returned to normal
mode) when the receiver is awakened.
SBK provides the ability to transmit a break code from the SCI. If the SCI is transmitting when SBK is
set, it will transmit continuous frames of zeros after it completes the current frame, until SBK is cleared.
If SBK is toggled (one to zero in less than one frame interval), the transmitter sends only one or two
break frames before reverting to idle line or beginning to send data.
SCSR contains flags that show SCI operational conditions. These flags can be cleared either by hard-
ware or by a special acknowledgment sequence. The sequence consists of SCSR read with flags set,
followed by SCDR read (write in the case of TDRE and TC). A long-word read can consecutively access
both SCSR and SCDR. This action clears receive status flag bits that were set at the time of the read,
but does not clear TDRE or TC flags.
If an internal SCI signal for setting a status bit comes after the CPU has read the asserted status bits,
but before the CPU has written or read register SCDR, the newly set status bit is not cleared. SCSR
must be read again with the bit set. Also, SCDR must be written or read before the status bit is cleared.
Reading either byte of SCSR causes all 16 bits to be accessed. Any status bit already set in either byte
will be cleared on a subsequent read or write of register SCDR.
TDRE is set when the byte in register TDR is transferred to the transmit serial shifter. If TDRE is zero,
transfer has not occurred and a write to TDR will overwrite the previous value. New data is not trans-
mitted if TDR is written without first clearing TDRE.
TC is set when the transmitter finishes shifting out all data, queued preambles (mark/idle line), or
queued breaks (logic zero). The interrupt can be cleared by reading SCSR when TC is set and then by
writing the transmit data register (TDR) of SCDR.
RDRF is set when the content of the receive serial shifter is transferred to the RDR. If one or more errors
are detected in the received word, flag(s) NF, FE, and/or PF are set within the same clock cycle.
0 = Normal receiver operation (received data recognized)
1 = Wakeup mode enabled (received data ignored until awakened)
0 = Normal operation
1 = Break frame(s) transmitted after completion of current frame
0 = Register TDR still contains data to be sent to the transmit serial shifter.
1 = A new character can now be written to register TDR.
0 = SCI transmitter is busy
1 = SCI transmitter is idle
0 = Register RDR is empty or contains previously read data.
1 = Register RDR contains new data.
NOT USED
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
9
TDRE
8
1
TC
7
1
RDRF
6
0
RAF
5
0
IDLE
4
0
OR
3
0
NF
2
0
MC68331TS/D
FE
$YFFC0C
1
0
PF
0
0