PIC18C452-E/PT Microchip Technology, PIC18C452-E/PT Datasheet - Page 141
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC18C452-E/PT
Manufacturer Part Number
PIC18C452-E/PT
Description
IC MCU OTP 16KX16 A/D 44TQFP
Manufacturer
Microchip Technology
Series
PIC® 18Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16C770-ISO.pdf
(8 pages)
3.PIC18C242-ISO.pdf
(305 pages)
4.PIC18C242-ISO.pdf
(12 pages)
Specifications of PIC18C452-E/PT
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
33
Program Memory Size
32KB (16K x 16)
Program Memory Type
OTP
Ram Size
1.5K x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
44-TQFP, 44-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
PIC18C452E/PT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18C452-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
- PIC16F616T-ISL PDF datasheet
- PIC16C770-ISO PDF datasheet #2
- PIC18C242-ISO PDF datasheet #3
- PIC18C242-ISO PDF datasheet #4
- Current page: 141 of 305
- Download datasheet (6Mb)
14.4.8
Transmission of a data byte, a 7-bit address, or the
other half of a 10-bit address, is accomplished by sim-
ply writing a value to the SSPBUF register. This action
will set the buffer full flag bit, BF, and allow the baud
rate generator to begin counting and start the next
transmission. Each bit of address/data will be shifted
out onto the SDA pin after the falling edge of SCL is
asserted (see data hold time specification parameter
106). SCL is held low for one baud rate generator roll-
over count (T
released high (see Data setup time specification
parameter 107). When the SCL pin is released high, it
is held that way for T
must remain stable for that duration and some hold
time after the next falling edge of SCL. After the eighth
bit is shifted out (the falling edge of the eighth clock),
the BF flag is cleared and the master releases SDA.
allowing the slave device being addressed to respond
with an ACK bit during the ninth bit time, if an address
match occurs, or if data was received properly. The sta-
tus of ACK is written into the ACKDT bit on the falling
edge of the ninth clock. If the master receives an
Acknowledge, the Acknowledge status bit, ACKSTAT,
is cleared. If not, the bit is set. After the ninth clock, the
SSPIF bit is set and the master clock (baud rate gener-
ator) is suspended until the next data byte is loaded into
the SSPBUF, leaving SCL low and SDA unchanged
(Figure 14-18).
After the write to the SSPBUF, each bit of address will
be shifted out on the falling edge of SCL until all seven
address bits and the R/W bit are completed. On the fall-
ing edge of the eighth clock, the master will de-assert
the SDA pin, allowing the slave to respond with an
Acknowledge. On the falling edge of the ninth clock, the
master will sample the SDA pin to see if the address
was recognized by a slave. The status of the ACK bit is
loaded into the ACKSTAT status bit (SSPCON2<6>).
Following the falling edge of the ninth clock transmis-
sion of the address, the SSPIF is set, the BF flag is
cleared and the baud rate generator is turned off until
another write to the SSPBUF takes place, holding SCL
low and allowing SDA to float.
14.4.8.1
In Transmit mode, the BF bit (SSPSTAT<0>) is set
when the CPU writes to SSPBUF and is cleared, when
all 8 bits are shifted out.
14.4.8.2
If the user writes the SSPBUF when a transmit is
already in progress, (i.e., SSPSR is still shifting out a
data byte), the WCOL is set and the contents of the
buffer are unchanged (the write doesn’t occur).
WCOL must be cleared in software.
2001 Microchip Technology Inc.
I
TRANSMISSION
2
BRG
BF Status Flag
C MASTER MODE
WCOL Status Flag
). Data should be valid before SCL is
BRG
. The data on the SDA pin
14.4.8.3
In Transmit mode, the ACKSTAT bit (SSPCON2<6>) is
cleared when the slave has sent an Acknowledge
(ACK = 0), and is set when the slave does not Acknowl-
edge (ACK = 1). A slave sends an Acknowledge when
it has recognized its address (including a general call),
or when the slave has properly received its data.
14.4.9
Master mode reception is enabled by programming the
receive enable bit, RCEN (SSPCON2<3>).
The baud rate generator begins counting, and on each
rollover, the state of the SCL pin changes (high to low/
low to high) and data is shifted into the SSPSR. After
the falling edge of the eighth clock, the receive enable
flag is automatically cleared, the contents of the
SSPSR are loaded into the SSPBUF, the BF flag bit is
set, the SSPIF flag bit is set and the baud rate genera-
tor is suspended from counting, holding SCL low. The
MSSP is now in IDLE state, awaiting the next com-
mand. When the buffer is read by the CPU, the BF flag
bit is automatically cleared. The user can then send an
Acknowledge bit at the end of reception, by setting the
Acknowledge
(SSPCON2<4>).
14.4.9.1
In receive operation, the BF bit is set when an address
or data byte is loaded into SSPBUF from SSPSR. It is
cleared when the SSPBUF register is read.
14.4.9.2
In receive operation, the SSPOV bit is set when 8 bits
are received into the SSPSR and the BF flag bit is
already set from a previous reception.
14.4.9.3
If the user writes the SSPBUF when a receive is
already in progress (i.e., SSPSR is still shifting in a data
byte), the WCOL bit is set and the contents of the buffer
are unchanged (the write doesn’t occur).
Note:
The MSSP module must be in an IDLE
state before the RCEN bit is set, or the
RCEN bit will be disregarded.
I
2
ACKSTAT Status Flag
C MASTER MODE RECEPTION
BF Status Flag
SSPOV Status Flag
WCOL Status Flag
sequence
PIC18CXX2
enable
DS39026C-page 139
bit,
ACKEN
Related parts for PIC18C452-E/PT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC18C452-I/P](/photos/6/61/66192/150-40-dip_tmb.jpg)
Part Number:
Description:
IC MCU OTP 16KX16 A/D 40DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC18C452-I/L](/photos/6/63/66325/150-44-plcc_tmb.jpg)
Part Number:
Description:
IC MCU OTP 16KX16 A/D 44PLCC
Manufacturer:
Microchip Technology
Datasheet:
![PIC18C452-E/L](/photos/6/63/66325/150-44-plcc_tmb.jpg)
Part Number:
Description:
IC MCU OTP 16KX16 A/D 44PLCC
Manufacturer:
Microchip Technology
Datasheet:
![PIC18C452-E/P](/photos/6/61/66192/150-40-dip_tmb.jpg)
Part Number:
Description:
IC MCU OTP 16KX16 A/D 40DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC18C452/JW](/photos/6/63/66338/150-40-cdip_tmb.jpg)
Part Number:
Description:
IC MCU EPROM 16KX16 A/D 40CDIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC18C452-I/PT](/photos/6/82/68251/c04-076_pt_tmb.jpg)
Part Number:
Description:
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TQFP,44PIN,PLASTIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC18C452](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
(PIC18Cxx2) High-Performance Microcontrollers
Manufacturer:
Microchip Technology
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: