AT89S52-24PI Atmel, AT89S52-24PI Datasheet - Page 13

• Manufacturer Part Number: AT89S52-24PI
• Description: IC MCU 8K FLASH 24MHZ 40-DIP
• Manufacturer: Atmel
• Series: 89Sr

Specifications of AT89S52-24PI

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: UART/USART
• Peripherals: WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -

Figure 10-1. Timer in Capture Mode
Table 10-2.
1919D–MICRO–6/08
Symbol
–
T2OE
DCEN
T2MOD Address = 0C9H
Not Bit Addressable
Bit
T2EX PIN
OSC
T2MOD – Timer 2 Mode Control Register
T2 PIN
–
7
Function
Not implemented, reserved for future
Timer 2 Output Enable bit
When set, this bit allows Timer 2 to be configured as an up/down counter
÷12
Figure 10-2
are selected by bit EXEN2 in T2CON. If EXEN2 = 0, Timer 2 counts up to 0FFFFH and then sets
the TF2 bit upon overflow. The overflow also causes the timer registers to be reloaded with the
16-bit value in RCAP2H and RCAP2L. The values in Timer in Capture ModeRCAP2H and
RCAP2L are preset by software. If EXEN2 = 1, a 16-bit reload can be triggered either by an
overflow or by a 1-to-0 transition at external input T2EX. This transition also sets the EXF2 bit.
Both the TF2 and EXF2 bits can generate an interrupt if enabled.
Setting the DCEN bit enables Timer 2 to count up or down, as shown in
mode, the T2EX pin controls the direction of the count. A logic 1 at T2EX makes Timer 2 count
up. The timer will overflow at 0FFFFH and set the TF2 bit. This overflow also causes the 16-bit
value in RCAP2H and RCAP2L to be reloaded into the timer registers, TH2 and TL2,
respectively.
A logic 0 at T2EX makes Timer 2 count down. The timer underflows when TH2 and TL2 equal
the values stored in RCAP2H and RCAP2L. The underflow sets the TF2 bit and causes 0FFFFH
to be reloaded into the timer registers.
The EXF2 bit toggles whenever Timer 2 overflows or underflows and can be used as a 17th bit
of resolution. In this operating mode, EXF2 does not flag an interrupt.
TRANSITION
DETECTOR
–
6
shows Timer 2 automatically counting up when DCEN = 0. In this mode, two options
C/T2 = 0
C/T2 = 1
–
5
EXEN2
TR2
–
4
CAPTURE
CONTROL
CONTROL
–
3
RCAP2H
TH2
EXF2
RCAP2L
–
2
TL2
Reset Value = XXXX XX00B
OVERFLOW
T2OE
1
TF2
DCEN
Figure
0
INTERRUPT
AT89S52
TIMER 2
10-2. In this
13